Search

Page 1 of 6 1 2 3 4

Search: Search took 1.00 seconds.

  1. Replies
    92
    Views
    5,792

    Did you seal up the oil seal flaw as per Group K ?

    Did you seal up the oil seal flaw as per Group K ?
  2. Replies
    26
    Views
    1,572

    It’s either a blocked fuel tap , blocked fuel...

    It’s either a blocked fuel tap , blocked fuel filter , or the filters under the needle and seats being blocked . Fuel pressure dropping at full throttle means the engine is using the excess fuel that...
  3. Replies
    8
    Views
    441

    2-Stroke It looks like we are doing similar builds, mine...

    It looks like we are doing similar builds, mine is a 2000 GP1200R. Check out my thread you will find some recommendations and useful tips from other forum members. I opted to do the tunnel...
  4. Thread: 66V head

    by WetTech
    Replies
    7
    Views
    432

    View Post

    Jeff, thats perfect. Thank you. Don’t wanna go crazy, just want to make use of a bit more octane to get a little more “oomph” so to speak.
  5. Replies
    8
    Views
    441

    2-Stroke View Post

    Probably gonna go DynaFly. I’ve seen and heard of too many destroyed pumps from Solas recently unless the GPR impellers are not affected by their quality issues.
  6. Thread: 66V head

    by WetTech
    Replies
    7
    Views
    432

    View Post

    Thanks! I’ll get in touch with him!
  7. Replies
    22
    Views
    1,465

    Wow ! mostly seen center cylinder seizure's on...

    Wow ! mostly seen center cylinder seizure's on the PV 12's gummed up carbs running lean I will need to check out !
  8. Replies
    22
    Views
    1,465

    I saw that article but I don’t understand why...

    I saw that article but I don’t understand why it’s there if it causes a problem. I mean, Yamaha put it in for a reason.
  9. Replies
    7
    Views
    457

    There are dozens, if not hundreds, of Yamaha...

    There are dozens, if not hundreds, of Yamaha boats that could use something like this. Can you share any info about who makes them for you?
  10. Replies
    7
    Views
    457

    Yes we get these made to order, also do weave as...

    Yes we get these made to order, also do weave as well
  11. Replies
    22
    Views
    1,034

    To me it looks like the center plug is lean and...

    To me it looks like the center plug is lean and already trying to destroy your new rebuild. The clean one on the right is either flooding so badly that it's washing the plug clean, OR maybe not...
  12. Replies
    22
    Views
    1,034

    The white plug is way too lean. You MUST richen...

    The white plug is way too lean. You MUST richen it or you'll burn up that cylinder very quickly.

    I really don't like the gray plug. That cylinder may be having a meltdown. Gray deposits often...
  13. Replies
    9
    Views
    313

    So the only suspect components between the...

    So the only suspect components between the battery (+) and the hot side of the lanyard switch (red wire), is the main fuse (30A) and the wire harness connector for the left hand control's lanyard...
  14. Replies
    15
    Views
    1,278

    2-Stroke I put the water temp sensor on and was able to...

    I put the water temp sensor on and was able to get the alarm off but still was not getting power or a click. Jumped the starter solenoid with a screwdriver and I got the starter to bump. Replaced...
  15. Replies
    5
    Views
    450

    1200: Yes, prime the oil lines. No need to run...

    1200:
    Yes, prime the oil lines. No need to run premix initially unless doing a full top end rebuild and even then it's not necessary.
    Tygon works fine everywhere.
    Consider doing the Oside Bill...
  16. Replies
    17
    Views
    1,389

    View Post

    I feel like I’m learning all over again. After a long hiatus I had no idea of all the additional maintenance required. Especially on 2strokes. ThAnkful for these forums and thankful for YouTube
  17. Replies
    11
    Views
    534

    I'm w Jonesy, needle arm height should be flush w...

    I'm w Jonesy, needle arm height should be flush w body of carb, check it w a razor blade.
    Your pop off is low for stock jetting as well or high if using the Oside recipe?
  18. Replies
    19
    Views
    897

    View Post

    I depend on these forums so much it’s not even funny! Definitely frustrating when there no conclusion or resolution!
  19. Replies
    1
    Views
    173

    Lesson in chasing a problem

    I have 2 GP1200R’s and an XLT1200 that I bought with a damaged engine. They all have the same engines and carbs , I am very experienced with this format yet I chased an imaginary “electrical “...
  20. Replies
    5
    Views
    310

    you'll need the spline holder tool to lock up the...

    you'll need the spline holder tool to lock up the assembly in a vise ( show at how to link above)

    That's not a stock prop as far as I can tell, might be an impros, which uses an internal wrench
    ...
  21. Replies
    5
    Views
    294

    Yes, that will make a very large different, less...

    Yes, that will make a very large different, less restriction into the engine. But that "ductwork" is a flame arrestor designed to stop sparks from coming out of the intake if something goes wrong....
  22. Replies
    19
    Views
    897

    Might want to add clunks to pickup lines while in...

    Might want to add clunks to pickup lines while in there.
  23. Replies
    7
    Views
    436

    WTB Thanks for the heads up, yes I did. I ended...

    Thanks for the heads up, yes I did.

    I ended up finding a Riva Rideplate and YF CF 19/19 prop used on ebay, so now only looking for:
    -Reed Petals (prefer carbon)
    -Milled or Aftermarket Head...
  24. Replies
    15
    Views
    1,278

    2-Stroke I was considering getting one from them. Ended up...

    I was considering getting one from them. Ended up purchasing a good case and new wsm cylinder and 3 pistons. I got all the gaskets, seals, powervalves and carb kits. The only thing I need is the...
  25. Replies
    4
    Views
    337

    Looks like the screen to your power washer...

    Looks like the screen to your power washer [emoji23]
Results 1 to 25 of 126
Page 1 of 6 1 2 3 4