Search

Type: Posts; User: SplishSplash

Page 1 of 8 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    1
    Views
    79

    Yes, Group K did that to prevent High RPM lean on...

    Yes, Group K did that to prevent High RPM lean on modified ski's
    According to them with the crossovers, the carbs would go lean after a few seconds at WOT, leading to burnt pistions.
    Here is the...
  2. What impeller did you get? Still have the old...

    What impeller did you get? Still have the old one? Maybe put it back on and see if your speed comes back.
    Was the part # on the brand new supercharger correct for your ski?
  3. Replies
    9
    Views
    161

    Well, it looks neglected in the engine...

    Well, it looks neglected in the engine compartment, missing parts, Toggle switches for what? No clamp or zip tie on cylinder 1 pisser
    Carbs probably need a good cleaning. But before you tear it...
  4. Replies
    15
    Views
    296

    60 compression and even on all cylinder is...

    60 compression and even on all cylinder is actually good, it would be low if the timing chain snapped because the valves are not opening.
    Simple to check, no "tearing into it" just remove the valve...
  5. Replies
    8
    Views
    145

    Well, your looking at Flywheel bolts as suggested...

    Well, your looking at Flywheel bolts as suggested
    Also a new timing chain
    Supertech valves and springs along with titanium retainers.
    Piston for the dropped one and rings on all 3
    All gaskets...
  6. Replies
    8
    Views
    159

    Your story sounds a lot how I got my 1990 650 SX...

    Your story sounds a lot how I got my 1990 650 SX
    It was a hull half burried in mud, full of ants and weeds
    The engine was a box of parts and the electrics were a mass of wires in a pile with things...
  7. Replies
    8
    Views
    159

    You need all the parts you listed? Starter and...

    You need all the parts you listed? Starter and bendix will just swap over with the engine
    I don't know enough about the 1995 TS for all the electrical stuff, bit one thing that is different is the...
  8. Replies
    8
    Views
    159

    Block same, no issue there

    Block same, no issue there
  9. Replies
    8
    Views
    159

    Not everything, no, the fuel pump on the stand up...

    Not everything, no, the fuel pump on the stand up is hull mounted and its integrated into the carb on the 95 TS.
    Electrical box is different
    Ride plate different
    Pitch of impeller probably...
  10. Is the boss above the crack for a head bolt? If...

    Is the boss above the crack for a head bolt? If so, has the head ever been off, and maybe the bolt was run in too far and bottomed out on the hole and cracked the block. Or the theads were not...
  11. What RPM's are you seeing at WOT? Normal or low?

    What RPM's are you seeing at WOT? Normal or low?
  12. Not sure about the GTX layout, but the RXP, the...

    Not sure about the GTX layout, but the RXP, the rectifier bracket is mounted to the battery holddown. Zipties (good ones) should be fine.
  13. You mount the rectifier at the end of the air...

    You mount the rectifier at the end of the air inlet tube that comes from the front of the seat area to the front compartment .
    Nothing to do with the kanaflex.
  14. How many hrs on the engine? Why are you wanting...

    How many hrs on the engine? Why are you wanting to replace the bearings?
    I did at 140 hrs, just ordered stock set and everything fit fine and clerances were spot on.
    You will need new con rod...
  15. 100% ride one before you consider it. The...

    100% ride one before you consider it. The "trixx" gets old fast, you will find yourself wanting more performance within a day of riding one. Coming from a 300 RXT you will even notice it more....
  16. Replies
    2
    Views
    166

    Yep, harder than upgrading the 04 with X charger,...

    Yep, harder than upgrading the 04 with X charger, valves, Fizzle intercooler, RRFPR and flywheel bolts. Install Riva tune
    Get you to the same if not better speed and acceleration point as the route...
  17. Replies
    2
    Views
    118

    Are you sure the solenoid is good? If you jump...

    Are you sure the solenoid is good? If you jump the terminals and it starts, is it running normally?
  18. Not sure if it's the camera angle in the cylinder...

    Not sure if it's the camera angle in the cylinder pics or not, but pic 1 and 2 seem to have the oil squirter partly or totally blocked, #3 is clear.
    Not that it caused the failure, just an...
  19. Well, are you 100% sure your oil pressure is ok? ...

    Well, are you 100% sure your oil pressure is ok? Have you checked to see if the oil filter has collasped?
    How may hrs on the engine?
    Where is the oil level at?
  20. Replies
    8
    Views
    206

    Check your fuses in the MPEM Check the new...

    Check your fuses in the MPEM
    Check the new battery voltage when you press start, new batteries can be bad.
    Check all your grounds, especially the 3 on the front of the engine
    Remove the spark...
  21. The throttle cable only needs a little slack at...

    The throttle cable only needs a little slack at idle, there is no nut to worry about. The throttle stop is the thing you never should touch, as that would require a recalibration.
  22. Bran new, don't even mess with them, straight...

    Bran new, don't even mess with them, straight back to dealer as this is a warranty issue. But do let us know what the dealer found.
  23. Replies
    32
    Views
    1,127

    Does look well done. Whats the button and LED...

    Does look well done.
    Whats the button and LED for?
    Can you ask the previous owner if the valves and flywheel bolts were ever done?
    The supercharger intake is just a short velocity stack? or is...
  24. Replies
    12
    Views
    265

    Did you clean the main filter under the fuel...

    Did you clean the main filter under the fuel inlet needle and seat? in the carb? There is a mesh screen there that can plug up. Sounds like it starving for gas.
    Part # 49019...
  25. Thats a compression test, you need to pressure...

    Thats a compression test, you need to pressure test the closed loop cooling system and see where the coolant is getting in.
    Is the oil good or is it getting milky?
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4