Search

Type: Posts; User: Myself

Page 1 of 8 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    46
    Views
    984

    Great job! Hoping the maiden voyage goes well.

    Great job! Hoping the maiden voyage goes well.
  2. Replies
    3
    Views
    122

    Are you going to part the engine or keep it...

    Are you going to part the engine or keep it complete?
  3. Just spin them by hand feeling for vibration or...

    Just spin them by hand feeling for vibration or anything that's not buttery smooth. Also ever so little axial play, they should feel tight.
  4. Replies
    6
    Views
    191

    I'm betting I never paid much attention to that...

    I'm betting I never paid much attention to that since it had 2 bolts holding it.
  5. Replies
    1
    Views
    63

    Some people have done that, some have bent the...

    Some people have done that, some have bent the sensor to point downstream and reinserted it, some people never get the alarm..........take your pick.
  6. Make sure those crank bearings are tight and...

    Make sure those crank bearings are tight and smooth.
  7. Replies
    6
    Views
    136

    I have that in my notes somewhere. The stock...

    I have that in my notes somewhere. The stock airbox has several 1" holes. You just go around that same edge and drill a whole bunch more.
    I always do euro specs with stock airbox and elbow and...
  8. Replies
    6
    Views
    191

    Here is the block they sent me.....

    Here is the block they sent me..
    https://www.yamahapartsnation.com/oemparts/partsearch/yamaha_personal_watercraft?partsearch=6cr-15100-11-00

    If you click the first one "where used" it appears to...
  9. Replies
    7
    Views
    166

    I've ridden a bunch of different skis and I think...

    I've ridden a bunch of different skis and I think the stx15f launches pretty hard.
  10. Replies
    6
    Views
    191

    I recently swapped all '10 model guts into a...

    I recently swapped all '10 model guts into a newer block. I ordered a new block per parts listing and it was superceded. It came with a new grounding block setup cause that was different. Everything...
  11. First...updated power valve keepers if it's not...

    First...updated power valve keepers if it's not been done. Cleaning while your in there. Also check/replace oil lines, clean/rebuild carbs. If it's not bouncing off the rev limiter the pump is...
  12. Replies
    10
    Views
    305

    Great! That is a very fair price.

    Great! That is a very fair price.
  13. If you were holding throttle open it WON'T spark....

    If you were holding throttle open it WON'T spark. Computer must see a closed throttle to start.
  14. I explain to my customers how important it is to...

    I explain to my customers how important it is to check under the seat. I literally count seconds out loud as I show them how to remove the seat, grab the engine and see if it's solid ( motor mounts),...
  15. Replies
    19
    Views
    377

    https://www.ebay.com/itm/Fuel-Pump-for-SeaDoo-XP-L...

    https://www.ebay.com/itm/Fuel-Pump-for-SeaDoo-XP-LRV-DI-2002-2004-HFP-342DI-Direct-Injection-204560259/113563826355?epid=6028142248&hash=item1a70ee78b3:g:zd8AAOSwhyZbtylP&redirect=mobile
  16. Replies
    19
    Views
    377

    The newest "quantum" fuel pumps look VERY similar...

    The newest "quantum" fuel pumps look VERY similar to the oem. I have used 2 this season and so far so good!!
  17. Thread: One More Try...

    by Myself
    Replies
    6
    Views
    136

    I'll check my notebook. Thinking around 45vac. ...

    I'll check my notebook. Thinking around 45vac.

    ...Found it!!
    Update and '00-'04
    Blk to pur excitor--- 5.5 ohms and 40-50vac while cranking, everything hooked up
    Yel to red/pur charge---0.75...
  18. Definately a lean meltdown as the pistons are...

    Definately a lean meltdown as the pistons are burnt up on the exhaust side. There is also no fuel wash on those piston tops to speak of. The 110 pilot and 125 main jetting sounds too small, I'm...
  19. Replies
    19
    Views
    377

    I am very familiar with DI machines and will try...

    I am very familiar with DI machines and will try to help out. You are on the right track by checking compression first. Also what do the spark plugs look like? That will also tell us how they were...
  20. Replies
    5
    Views
    141

    The saltwater causes the aluminum corrosion that...

    The saltwater causes the aluminum corrosion that swells behind the stainless ring. Can you get a new ring or have the machine shop wrap and weld a new piece of stainless? The corrosion really needs...
  21. Replies
    19
    Views
    864

    I don't care who does the machine work....ALWAYS...

    I don't care who does the machine work....ALWAYS check clearance and ring end gap before installing pistons. It only takes an extra 5 minutes, not worth any potential headaches like this without...
  22. Thread: One More Try...

    by Myself
    Replies
    6
    Views
    136

    One of the first things I do anymore on the 700...

    One of the first things I do anymore on the 700 with no spark is check ac output voltage of the excitor.......normally where I find the issue.
  23. I've seen many like that. You can buy a starter...

    I've seen many like that. You can buy a starter repair kit.
    ...
  24. Replies
    4
    Views
    741

    Yes, they are the same size but compression is a...

    Yes, they are the same size but compression is a bump up. Need to do all 4 at the same time.
  25. Replies
    12
    Views
    320

    I had one doing that and it had a bad bypass...

    I had one doing that and it had a bad bypass valve. Funny thing is that same vakve worked just fine on his other ski.
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4