Search

Page 1 of 7 1 2 3 4

Search: Search took 1.00 seconds.

  1. Replies
    25
    Views
    1,585

    If it ran OK before, then it's not trying to...

    If it ran OK before, then it's not trying to start in the wrong direction.

    I don't think you can change the direction of the starter without re-wiring the brush plate inside the starter (not...
  2. Replies
    6
    Views
    558

    Doesn't look as bad as I expected. Can you...

    Doesn't look as bad as I expected. Can you rotate the crank and take close-up pictures of the rod bearings? We need to see the needles in the slots. They should be clean and shiny. It would...
  3. Replies
    3
    Views
    317

    waste of money

    waste of money
  4. Replies
    2
    Views
    226

    all 1200pv cases are pretty much the same. 1300...

    all 1200pv cases are pretty much the same. 1300 cases will work too just have to add pulse line nipples
  5. Replies
    9
    Views
    773

    I have a good core crank. Whats it worth?

    I have a good core crank. Whats it worth?
  6. well you now qualify for the annual Captain Pete...

    well you now qualify for the annual Captain Pete award, given when somebody ignores good advice and turns out successful, against all odds

    congratulations
    ...
  7. Replies
    10
    Views
    742

    I havent had any issues with parts unlimited poly...

    I havent had any issues with parts unlimited poly fuel line
  8. Replies
    15
    Views
    528

    There are 3 yellow wires coming from the back of...

    There are 3 yellow wires coming from the back of the PTO housing from the stator. This is what generates power to the VR. There is a connection half way on the right side you need to check for...
  9. Replies
    9
    Views
    607

    People are idiots

    People are idiots
  10. Thread: 1996 SPX

    by Wire4Money
    Replies
    16
    Views
    1,113

    View Post

    Thatís a factory non dess kill switch.
  11. Replies
    9
    Views
    645

    From what I understand these Little dimples On...

    From what I understand these Little dimples On each end of the surface of the head are indicators.

    When you get flush with the depth of the dimples then you will need a thicker gasket.
  12. You will get continuity through the motor...

    You will get continuity through the motor windings.
  13. Replies
    15
    Views
    491

    Yeah 96 tank will come out, but dont think 97...

    Yeah 96 tank will come out, but dont think 97 will, pretty sure 97 has the extra fuel cap added at the back of tank (much wider at the rear )
    On the 700's I've been able to change stator in the hull.
  14. Replies
    22
    Views
    1,757

    get a good flashlight and take a look into the...

    get a good flashlight and take a look into the stern area of the hull. My bet would be the rideplate fittings are leaking do to the low quality spring clamp that's been used by seadoo. careful..the...
  15. Replies
    38
    Views
    5,306

    This might help. ...

    This might help.


    http://greenhulk.net/forums/attachment.php?attachmentid=475333&stc=1
  16. Replies
    5
    Views
    669

    Except for problems with the head, pistons,...

    Except for problems with the head, pistons, supercharger, intercooler and jet pump... it's a great JetSki.

    Make sure it's shiny and looks good. You'll spend more time looking at it than riding it.
  17. If you never actually removed the rv itself and...

    If you never actually removed the rv itself and inspected the rv surface on the engine block it still needs to be looked at

    You donít see lines on the cover section unless something went down the...
  18. one way valve for the bildge pump hose i believe

    one way valve for the bildge pump hose i believe
  19. Replies
    15
    Views
    1,017

    Most all reliability mods have been done, Ask if...

    Most all reliability mods have been done, Ask if the oil injection lines have been replaced.
  20. Replies
    10
    Views
    1,269

    You pretty much can't truly hone them as the...

    You pretty much can't truly hone them as the nikasil is really hard. You can use dingleball hone to deglaze them but it really won't do much more than that. I am not telling you that you should, I...
  21. Sounds like a stuck starter relay kinda common

    Sounds like a stuck starter relay
    kinda common
  22. Replies
    4
    Views
    405

    Have you pulled the feed from the tank and...

    Have you pulled the feed from the tank and inspected it? Replaced fuel lines from tank to carbs? Would be my first action
  23. Replies
    19
    Views
    798

    You can look up factory parts here:...

    You can look up factory parts here: https://parts.polarisind.com/Browse/Browse.asp
    It looks like it used the same gasket as all other Keihin carbs.

    Sorry, but I do think yours is the only one . I...
  24. Replies
    8
    Views
    1,501

    you probably should not leave it in the water...

    you probably should not leave it in the water
    salt water is bad stuff and it will mess up your ski very quickly
  25. Replies
    3
    Views
    545

    If it pressure tested fine, no oil in coolant or...

    If it pressure tested fine, no oil in coolant or coolant in oil, and its not dropping then I would not worry, its just the paint or what ever the black stuff is on the gasket flaking off a bit.
Results 1 to 25 of 173
Page 1 of 7 1 2 3 4