Search

the first thing I would look at here is the triangular shaped connector that brings the yellow wires from the stator to the wire harness. It is a very common failure point on 07 models bother pwc and...

I had to install something similar on the clutch linkage on my F150, a heavy wear item and the plastic bushings just implode once the ball on the clutch linkage wears ( and a 30 year old truck has...

I recall a forum message on this subject last year..a quick search turned up this guy:

https://www.rhaasproducts.com/ProductDetails.asp?ProductCode=STRNUT

kawasaki only at this vendor but it...

that's why I asked about oem or third party, the very first time I had to do a steering cable ( I job I learned to dread from a pal who runs the big boat shop in town) I went OEM as they were...

global has the steel ar mags for $7 (limit 23!)

https://globalordnance.com/shk-30rd-steel-ar15-magazines-upc-00850003223070/

KyGunco has the amend 2 plastic mags for the ar for $8.75
...

get accustomed to removing the deck, its pretty bad first few times, then its somewhat bearable. You can rig a simple block and tackle setup on an a-frame to lift the top out of the way, then put the...

I'd suggest doing an end to end check on the blower wiring with your voltmeter. That's a vital item that you simply cannot be safely operating without. You might want to pull the switch panel from...

You have been redeemed....

If your engine is in stock configuration and in good time no need to pay extra for a starter

Starters typically fail due to cranking repeatedly in a situation I like to call “crank and pray(the...

It’s typical when writing software that has to support multiple variants if hardware(I have a considerable amount of experience in this area having worked on remote control software for digital...

And....?

And.....?

aftermarket mpems that do not use the DESS system run around $250 or less. These aftermarket units just look for the magnetic switch on the post closing indicating that there is "a key" installed to...

get an inspection camera ( they are under $40 on amazon) and have a look inside of each cylinder.

if there are no signs of carnage or heavy rust, fill each cylinder with marvel mystery oil and let...

welcome aboard GH

use the search feature and you'll find its pretty common for an oil pressure sensor to throw a "red herring" code. Its a fairly common failure point.

you do not want to...

it's likely that just tightening anything will resolve a leak issue, but by all means give everything a very small tweek. More likely that the cable seals were not installed correctly and were...

put a voltmeter on the starter side of the solenoid. if you see 12v on it when you hit the button, investigate battery leads

if you see zero to 3 volts on it, most likely your starter is fried
...

on the surface, my take would be:

(a) a vessel subject to the rules IF the cabin is not enclosed
(b) if the vessel is exempt under sections of the regulation

looks like several accidents have...

hmmmmm

If it was me, I'd:

"read vehicle"
"erase all keys"
"add new Key"
"Write vehicle"

there is a possibility that a different key making system was used on this ski at one time and the...

Didi I miss the news reports or did gangs of white folks start burning down every MacDonald store in Pittsburgh and adjacent towns?

how many keys are showing on the list?..grayed out write tells me the list might be full.

some screenshots might be helpful, but I suspect the candoo crew will have a quick answer

follow ups are the gold of the forum. Good work.

for supercharged models the position of the clamp for the ptp boot/bearing is quite important.

it's a common problem on older seadoo that the rotary valve seals leak and can eventually fill the crankcases with injection oil.

there have been numerous threads on the forum on how to address...

they can be really difficult to start due to small variances in the pump itself

if its an oem color coded ring I recall a notice in the box about using the chamfered end to go into the pump

a...

yeah that's about right and if done right you should be good for a couple of hundred hours of fun