Search

Type: Posts; User: ncdoo

Page 1 of 8 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    852
    Views
    320,605

    Sticky: When all else fails, get a bigger hammer. Not...

    When all else fails, get a bigger hammer. Not really. Seriously I've had them where they'll hardly budge, especially salt water skis. If they're that stubborn I use a dead blow hammer and a piece of...
  2. Replies
    3
    Views
    89

    I agree

    I agree
  3. Replies
    2
    Views
    111

    Plenty of threads on this. No real performance...

    Plenty of threads on this. No real performance gain, just makes it louder.
  4. Replies
    7
    Views
    85

    That will work also.

    That will work also.
  5. Replies
    7
    Views
    85

    787 engine correct? No you have to leave it. It...

    787 engine correct? No you have to leave it. It also feeds the rotary valve gear cavity. Just disconect the line going to the oil pump and block it off. You need to remove the oil pump also along...
  6. Just get a piece of pvc pipe a little bigger than...

    Just get a piece of pvc pipe a little bigger than the nut, heat it up then slip it over the nut and hold for a few seconds until the pvc hardens up. There is a post here on how to do it, but I cant...
  7. Replies
    6
    Views
    137

    You should be able to pick up a good used one...

    You should be able to pick up a good used one cheap on ebay or in the classified. Always go back with OEM parts, you'll thank me later. I may have one, PM me.
  8. Pretty sure he means VXR.

    Pretty sure he means VXR.
  9. Actually the bearing dont look that bad. The...

    Actually the bearing dont look that bad. The discoloration is mainly from the heat treating when the crank was manufactured.
  10. Replies
    11
    Views
    1,373

    FS - Parts bump

    bump
  11. Replies
    16
    Views
    2,960

    FS - Parts One black left

    One black left
  12. Replies
    36
    Views
    5,020

    FS - Parts One set left

    One set left
  13. Replies
    6
    Views
    463

    WTB - Parts Bump

    Bump
  14. Steering cable is probably the easiest job you'll...

    Steering cable is probably the easiest job you'll do on a jet ski, besides changing the plugs. You can make the tool from a piece of pvc pipe.
  15. Replies
    2
    Views
    180

    You should not be smelling gas in the hull. You...

    You should not be smelling gas in the hull. You need to find the leak. Sorry to say but this will most likely entail removing the suspension deck to physically locate the source of the leak.
  16. Replies
    1
    Views
    106

    No maintenance required especially if you have a...

    No maintenance required especially if you have a stock ski. If you get bored, you can always pull it out and check the slip.
  17. Replies
    2
    Views
    90

    Each carb will be different, set them to the...

    Each carb will be different, set them to the correct ampount of turns from seated and you'll be fine.
  18. Replies
    7
    Views
    149

    Uh, no.

    Uh, no.
  19. Replies
    11
    Views
    532

    There's a guy parting out his 85 mph RXP in the...

    There's a guy parting out his 85 mph RXP in the classifieds, gives you a good indication of what you'll need.
    http://greenhulk.net/forums/showthread.php?t=277083
  20. Replies
    22
    Views
    512

    Looks seated to me.

    Looks seated to me.
  21. Replies
    22
    Views
    512

    Is the valve bent? Hard to tell from the pic....

    Is the valve bent? Hard to tell from the pic. That could explain it.
  22. Replies
    22
    Views
    512

    Never seen that, that's where the fuel injector...

    Never seen that, that's where the fuel injector should be. Maybe had a leak and fire at that injector?
  23. Replies
    22
    Views
    512

    That's odd, got a pic?

    That's odd, got a pic?
  24. Thread: 215 SC wheel

    by ncdoo
    Replies
    6
    Views
    175

    WTB - Parts PM me when you get one.

    PM me when you get one.
  25. Replies
    9
    Views
    263

    I don't think that was the question.

    I don't think that was the question.
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4