Search

Type: Posts; User: Mockingee

Page 1 of 8 1 2 3 4

Search: Search took 0.03 seconds.

  1. Are the carbs opening fully?

    Are the carbs opening fully?
  2. Replies
    1
    Views
    243

    WTB - Parts Nobody with any good used sets?

    Nobody with any good used sets?
  3. Replies
    6
    Views
    209

    I also suspect the drive coupler. If not that ,...

    I also suspect the drive coupler. If not that , there’s something wrong in the jet pump somewhere, maybe something else is stripped, drive shaft or inside impeller?
  4. Replies
    1
    Views
    243

    WTB - Parts WTB 1200 Piston and cylinder sets

    Hi,

    Iím looking for two ready to install piston and cylinder sets for my 2002 1200 Genesis i.

    Thanks
  5. Replies
    14
    Views
    1,041

    It's no problem to read the codes. Do some...

    It's no problem to read the codes. Do some digging in K447's signature links. Somewhere in there is how to build a code reader for near nothing and how to use it.
  6. Look at that, I stand corrected.

    Look at that, I stand corrected.
  7. I don't think that will help as The end of the...

    I don't think that will help as The end of the starter only goes into the bendix drive. The bendix drive cannot be taken out through the hole the starter is in, therefore banging on the bendix will...
  8. The oil tank thing is a known issue. Put a couple...

    The oil tank thing is a known issue. Put a couple of O-rings around the sensor bung and shove it back in. Add a hose clamp around the tank neck.
  9. You can turn the engine by hand by grasping the...

    You can turn the engine by hand by grasping the drive coupler, (where the driveshaft is coupled to the motor) at the rear of the motor. There might be a small plastic cover over it. If you can't turn...
  10. Before replacing the starter, make sure it is...

    Before replacing the starter, make sure it is well grounded. Check the spots where ground cables are bolted on the engine block for oxidation.

    Have you checked to make sure you can turn the engine...
  11. Replies
    5
    Views
    742

    If I understand what you are saying it sounds...

    If I understand what you are saying it sounds like you plan to use the crank from the flooded ski. If that's the case and the engine was indeed flooded there is almost certainly rust on the crank...
  12. You say a friend sold it to you? Are you sure...

    You say a friend sold it to you? Are you sure he's a friend? Looks like somebody went snip happy.
  13. Replies
    7
    Views
    708

    SOLD Wow, wish I lived closer, or at least in the same...

    Wow, wish I lived closer, or at least in the same country.
  14. Replies
    12
    Views
    618

    Here in Nova Scotia Canada that would be a dream...

    Here in Nova Scotia Canada that would be a dream buy. I can't even fix my Genesis for $1500 US.
  15. Replies
    26
    Views
    1,122

    I would think if you take the plug out of the...

    I would think if you take the plug out of the flywheel cover and turn the engine a bit you should be able to tell if there's fuel in there. If there's only a bit I would think the flywheel would be...
  16. Replies
    26
    Views
    1,122

    Since your ski is oil injected your crankcase...

    Since your ski is oil injected your crankcase filling with raw fuel has now rinsed every bit of lubrication from the crank and rod bearings, (bottom and wrist pin). Maybe I'm being overly paranoid...
  17. Replies
    26
    Views
    1,122

    That used to happen to old snowmobiles. I assume...

    That used to happen to old snowmobiles. I assume it should be the same for your ski. By the way, does your ski have oil injection or premix?
  18. Replies
    10
    Views
    1,430

    8 volts while cranking is normally not enough...

    8 volts while cranking is normally not enough power to make it go. You're lucky it starts at all.

    I'm wondering if something's binding or dragging, possibly in the jet pump. If you take out the...
  19. Replies
    8
    Views
    593

    I'm not claiming to have the knowledge and...

    I'm not claiming to have the knowledge and experience of some of the other guys on GH, in fact I openly state I do not but if the limited experience I do have can be helpful that's great.

    By by...
  20. Replies
    8
    Views
    593

    Just some info from my own experience. At one...

    Just some info from my own experience. At one point my genesis would not spark or run the fuel pump. I did the stator test as you mentioned above and the voltage was off a very small amount. Around 1...
  21. Replies
    19
    Views
    914

    One question. Does the flat spot you created...

    One question. Does the flat spot you created happen to be parallel to the factory slot in the shaft? That would certainly make things easier.
  22. Replies
    19
    Views
    914

    This is great. One more obsolete part that is no...

    This is great. One more obsolete part that is no longer unobtainable. Koodos for figuring this out. Every time I put $ into my Genesis I worry about whether or not I should be spending it on a...
  23. Replies
    18
    Views
    979

    Deleted. My post was about a two stroke.

    Deleted. My post was about a two stroke.
  24. Replies
    18
    Views
    737

    As far as I know, used OEM is it. Nobody makes...

    As far as I know, used OEM is it. Nobody makes them new. Consider the post above. He won't rip u off.
  25. Replies
    3
    Views
    515

    For new parts there's SBT in Florida and...

    For new parts there's SBT in Florida and CVTech-AAB in Wisconsin, just to name a couple. There are also some parts dealers here on the Greenhulk Forum who may post on your thread.
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4