Search

Type: Posts; User: Mockingee

Page 1 of 8 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    18
    Views
    387

    I don’t understand. Are you saying the coupler is...

    I don’t understand. Are you saying the coupler is turning but not umthreading from the crank? How are you keeping the crank from turning?
  2. Not too much oil, rich on fuel.

    Not too much oil, rich on fuel.
  3. Looks like the PTO cylinder is very rich.

    Looks like the PTO cylinder is very rich.
  4. Read what K447 pointed you to. Do the stator...

    Read what K447 pointed you to. Do the stator checks as a good place to start.
  5. Replies
    131
    Views
    1,731

    O OK. I was born in Berwick.

    O OK. I was born in Berwick.
  6. Replies
    131
    Views
    1,731

    Where are you in NS? I’m outside of Windsor.

    Where are you in NS? I’m outside of Windsor.
  7. Replies
    131
    Views
    1,731

    If the ignition timing is on enough to start it...

    If the ignition timing is on enough to start it with a prime it should be on enough to start it with injected fuel. Also, the DI motors usually backfire badly with the ignition timing off. How long...
  8. Replies
    17
    Views
    374

    Does it test properly while actually bolted in...

    Does it test properly while actually bolted in place?
  9. Replies
    16
    Views
    282

    Not to be a stickler but Polaris recommended red...

    Not to be a stickler but Polaris recommended red thread locker on the snout of the crankshaft when reinstalling the flywheel, and while your “rattle gun” is great for removing the tight flywheel nut,...
  10. Replies
    8
    Views
    203

    Was the flywheel cover gasket good? The starter...

    Was the flywheel cover gasket good? The starter has one or two O-rings on it that seal the opening where it goes into the flywheel housing. Check there.
  11. I’m not familiar with the MSX hull but in my...

    I’m not familiar with the MSX hull but in my Genesis the resonator sits way in the rear of the hull, all packed in with styrofoam. If you follow the path of the diagram provided above you should be...
  12. I also understand your $$$ concerns, however, at...

    I also understand your $$$ concerns, however, at least in my experience, boating of any kind is expensive. I read some stories on the forum about people buying skis with very little wrong for very...
  13. Replies
    8
    Views
    175

    Taking a quick look on eBay I don’t see an...

    Taking a quick look on eBay I don’t see an Evinrude flywheel that looks as if it would fit on a Polaris.
  14. If I were you I would be concerned about crank...

    If I were you I would be concerned about crank and rod bearings in that cylinder. I’m no expert but that doesn’t look like pieces of soft aluminum to me. Could be ring I guess, if any pieces are...
  15. Replies
    9
    Views
    418

    Looks like he’s poked a hole in a plastic bag,...

    Looks like he’s poked a hole in a plastic bag, taped the cable into said hole, put some oil in the bag and then hung the whole works from a bungee cord.
  16. Replies
    2
    Views
    156

    I’m guessing engines like that for sale used are...

    I’m guessing engines like that for sale used are rare, and pricey.
  17. Before you decide to rebuild your engine, open up...

    Before you decide to rebuild your engine, open up the case and see if the crank bearings spun inside the case, enlarging the bearing bores. You want to know if you have a good case before you decide...
  18. Replies
    11
    Views
    638

    Makes sense. I’ve seen bent/broken rods but not...

    Makes sense. I’ve seen bent/broken rods but not cracked cylinders. Then again, I’ve not seen one of these flooded with water.
  19. Thanks HiPeRcO. Merry Christmas, Happy New Year...

    Thanks HiPeRcO. Merry Christmas, Happy New Year and all the best to everyone.
  20. Replies
    11
    Views
    638

    Right, I keep forgetting not everybody has Nova...

    Right, I keep forgetting not everybody has Nova Scotia temperatures. I wonder what caused everything to crack.

    As suggested above, a good used motor is probably your best option. Hopefully they’re...
  21. Replies
    11
    Views
    638

    Everything you describe sounds as if it froze...

    Everything you describe sounds as if it froze with everything full of water. I just can’t figure out how that’s possible. As far as my experience goes, the water runs out when you pull it out of the...
  22. Replies
    11
    Views
    638

    My advice is pull the motor. If it has the damage...

    My advice is pull the motor. If it has the damage you described it’s bound to have more. I would inspect every part of that motor before putting it back together.
  23. The motors are basically the same. As u said, u...

    The motors are basically the same. As u said, u will have to change the heads, flywheel, stator, etc... I have heard that some DI motors don’t have a pulse nipple for the carb fuel pump but I can’t...
  24. There was a post a while back about a member...

    There was a post a while back about a member having a 505 in a FICHT ski. Going from memory, it would run but not charge. Also, who knows what damage may have been done in the long run.
  25. Replies
    13
    Views
    599

    Will a bad TPS cause a no spark condition? What...

    Will a bad TPS cause a no spark condition? What does it do with the TPS unplugged?
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4