Search

Type: Posts; User: smokeysevin

Page 1 of 8 1 2 3 4

Search: Search took 0.04 seconds.

  1. I relized I had a problem when I picked up my 15f...

    I relized I had a problem when I picked up my 15f and stxr and got them back to my garage only to realize I grabbed the wrong non running stxr...

    Sean
  2. FS - Parts Yep, its really damn heavy though. I would say...

    Yep, its really damn heavy though. I would say probably $100+ for shipping. I can put the cylinders and covers back on to make it more compact but it will still be pricey.

    PM me a...
  3. Inner Glasswork Part 3 (Where you feel like you...

    Inner Glasswork Part 3 (Where you feel like you are ready for some corners so you get wrecked)

    I rolled the hull upside down and attempted to layup the inner hood flange and hood to nose flange....
  4. FS - Parts Kawasaki 1100 motor (needs rebuild, may be scrap)

    Cases and head look good, otherwise I can't say much.

    Make an offer, I just need it gone.

    Sean ...
  5. Inner Glasswork Part 2 I rolled the hull over...

    Inner Glasswork Part 2

    I rolled the hull over onto the other side and repeated the process. Fortunately my template worked on both sides and I ended up with reasonably well fitting repairs on...
  6. FS - Parts Kawasaki piston port js550 parts (exhaust, intake, motor)

    Few parts and a complete but disassembled and in need of rebuild motor.

    Orange county jetski exhaust

    Breadbox jetpower exhaust

    Mystery exhaust

    Make an offer, its just taking up space.
  7. FS - Parts Kawasaki 650 long block and bed plate

    1989? 650 put of a TS. I bought it a week or so ago then came across a 750 for the right price so let my shortsightedness be your gain! I have a magneto cover on the way as well as a flywheel,...
  8. Replies
    0
    Views
    39

    FS - Parts 1997 Kawasaki STX 1100 Complete

    1997 Kawasaki STX 1100 Complete

    the ski has been sitting for a few years and had the following work done to it before being put into storage:

    clean used oem cdk carbs installed
    Choke removal...
  9. Inner Glasswork Part 1 The hull is sitting on...

    Inner Glasswork Part 1

    The hull is sitting on its side now with the inside was stripped out, scuffed with 80 grit and wiped with alcohol to remove excess dust. I put one layer of 1208 fiberglass...
  10. Stripping the hull part 1 Got the ski totally...

    Stripping the hull part 1

    Got the ski totally stripped with the exception of the pump and driveline yesterday. I cleaned up one side of the inner engine bay and rolled the hull up on its side to...
  11. Well, it has come to this. My life has spiraled...

    Well, it has come to this. My life has spiraled totally out of control and I now have to actually finish projects instead of just getting more and forgetting about them.

    Teardown

    I got started...
  12. Replies
    16
    Views
    1,173

    Do the resealed hulls flex any more than stock...

    Do the resealed hulls flex any more than stock and what did you do to separate them?

    Sean
  13. Replies
    6
    Views
    558

    You can check the microfiche online just look at...

    You can check the microfiche online just look at the part numbers. Bikebandit.com s one of the easier ones to use.

    Sean
  14. Replies
    4
    Views
    496

    I have 2 on my bench now. If I remember I will...

    I have 2 on my bench now. If I remember I will post my measurements up tomorrow.

    Sean
  15. Have yall had issues with the caps cracking near...

    Have yall had issues with the caps cracking near the threads where the hose/spout threads in? My caps all seem to die on the seam there even if I don't tighten them all that much. I have been...
  16. FS - Parts Bump Sean

    Bump

    Sean
  17. Replies
    5
    Views
    279

    Slide it on until it stops. Make sure you have...

    Slide it on until it stops. Make sure you have the rings fully seated, wrap them with a thin layer of paper tape or painters tape just enough to hold the rings in place. The factory just intalls a...
  18. Replies
    9
    Views
    545

    Thats great, thanks for posting it. Sean

    Thats great, thanks for posting it.

    Sean
  19. Replies
    77
    Views
    3,123

    Made a fixture plate to bore the kawasaki...

    Made a fixture plate to bore the kawasaki driveshaft thru hull out to fit the doo driveshaft and carbon seal carrier.

    Swag offroad tube notcher shaft(1" Version)
    3/8 Milwaukee hole saw arbor
    ...
  20. Replies
    11
    Views
    626

    I agree, the coupler is probably too close. The...

    I agree, the coupler is probably too close. The rear output shaft bearing is a pretty tight fit to the output stub shaft iirc and has the rear motor mounts cast into it.

    I have one our now of you...
  21. Replies
    2
    Views
    853

    That's cute. I have 2 like this that are probably...

    That's cute. I have 2 like this that are probably going go cost me more than they are worth to get back to good. If they hadn't been free I would have said no.

    Sean456042
  22. FS - Parts Kawasaki 4 stroke parts, pistons, cams, pumps, props.

    1 set of forged mtc pistons, stock compression ratio

    3 oem stx 15f pistons

    4 oem ultra 250 pistons

    1 modified ultra 250 155mm exit nozzle bored for nozzle rings 83mm, 84mm and 85mm rings.
    ...
  23. I was going to suggest using marine tex on the...

    I was going to suggest using marine tex on the small chunk but then I saw the keel. It my need to get flipped and re-gelkoted.

    Sean
  24. Replies
    5
    Views
    427

    WTB - Parts Pm sent Sean

    Pm sent

    Sean
  25. Replies
    7
    Views
    550

    Check the thread in my signature. If you pull the...

    Check the thread in my signature. If you pull the pumps, don't crank the motor over with the starter. Only rotate the engine by hand.

    If the gauges are bad, I can flash the ecus to 2004 spec to...
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4