Search

Type: Posts; User: steve45

Page 1 of 8 1 2 3 4

Search: Search took 0.07 seconds.

  1. I don't have them, but I DO have a flywheel and...

    I don't have them, but I DO have a flywheel and related parts for a '91 Jet Mate 650. The Jet Mate uses different parts because the generator output is a little higher because it's classified as a...
  2. I drilled out the two 'retaining pins' that...

    I drilled out the two 'retaining pins' that secure the liner into the housing. It didn't fall out. I guess I'm going to have to get some steel plate and turn it on the lathe to make it fit, then...
  3. Replies
    1
    Views
    225

    Shredmaster Ride Plate On Ebay

    There's a Shredmaster ride plate for the Ultra 150 on Ebay for $750:
    ...
  4. Replies
    6
    Views
    460

    Got a big vise? Put the crank in the vise and...

    Got a big vise? Put the crank in the vise and remove the bolt in the center. It may have LocTite on it, so if it doesn't come off fairly easily, try some heat on the bolt.

    There should be some...
  5. Replies
    6
    Views
    460

    I've done a bunch of rehabs and ended up losing...

    I've done a bunch of rehabs and ended up losing money on most of them. I'd suggest trying to find a wrecked 'Ski that uses the same engine. You'll spend a fortune fixing that engine.
  6. Replies
    7
    Views
    357

    That boat is impressive! Nice shop, too! ...

    That boat is impressive!

    Nice shop, too! Clausing mill, CNC plasma cutter, welders...

    Do you do plasma cutting professionally, or just for fun?
  7. Replies
    2
    Views
    137

    As K447 said, most of the Yamahas are self...

    As K447 said, most of the Yamahas are self draining. If you were to flush it after saltwater use, keep this in mind:

    If you were to use that pump, it's quite possible that it would supply too...
  8. It's a joke. Engineers aren't civil. Surprised...

    It's a joke. Engineers aren't civil. Surprised you haven't heard that one.

    BTW, I have a degree in Mechanical Engineering and I had two roommates that were Civil Engineers.
  9. Replies
    45
    Views
    4,115

    OK, but if you had countersunk through bolts, you...

    OK, but if you had countersunk through bolts, you wouldn't have holes in your hull.
  10. Replies
    11
    Views
    396

    I got the pins. The holes in the panels are 6.47...

    I got the pins. The holes in the panels are 6.47 mm & 6.67 mm, with the larger hole being in the outer panel. The 6 mm pins are the right diameter, but they are too short to use in this...
  11. Replies
    9
    Views
    641

    I thought all the pumps after about 2013 had the...

    I thought all the pumps after about 2013 had the upgrade, but you're right--they don't! YES, do this upgrade!
  12. Alright! I'm glad you want to save another 150!...

    Alright! I'm glad you want to save another 150!

    Check the jet pump for rotation. It may have been good when you got it, but corrosion can push the liner into the impeller. New parts are not...
  13. Replies
    45
    Views
    4,115

    Team Bilford, I think you're overthinking this. ...

    Team Bilford, I think you're overthinking this. It's just a board bolted to some brackets. They wear out and need to be replaced every few years, just keep an eye on them. If you put through bolts...
  14. Replies
    45
    Views
    4,115

    I like the bunk rails long in the back. As K447...

    I like the bunk rails long in the back. As K447 said, it makes loading easier.

    I intentionally made the rear crossbeam of my trailer well behind the back of the 'Skis so I could have a good...
  15. Replies
    5
    Views
    558

    4200 is silicon and isn't rated for continuous...

    4200 is silicon and isn't rated for continuous immersion in water. 5200 is polyurethane and is rated for continuous immersion. 5200 is very hard to remove.

    For sealing ride plates, jet pumps,...
  16. Replies
    32
    Views
    3,160

    Got the new backup plate installed, what a pain!...

    Got the new backup plate installed, what a pain!

    http://greenhulk.net/forums/attachment.php?attachmentid=488658&stc=1 http://greenhulk.net/forums/attachment.php?attachmentid=488659&stc=1
  17. Nice find!

    Nice find!
  18. Replies
    5
    Views
    558

    Replacement For 3M 5200?

    3M 5200 is a well known polyurethane adhesive-sealant that holds up to water well and is strong & flexible. It is expensive and getting harder to locate.

    I was in Walmart today and saw a new...
  19. Replies
    45
    Views
    4,115

    I guess that they've changed the size. BE...

    I guess that they've changed the size. BE CAREFUL when launching and loading! Those things are very slippery. Don't unhook your safety cable until the 'Ski is over the water.
  20. Replies
    11
    Views
    559

    MadHatter, in your case, I think the best...

    MadHatter, in your case, I think the best solution would be to make a plug out of brass. You could put a hex end on it with an O-ring. This would be much better than the plastic that Kawasaki uses....
  21. Replies
    11
    Views
    559

    Well, it was worth a shot.

    Well, it was worth a shot.
  22. Replies
    11
    Views
    559

    Thanks, Mike! I'm looking for the Pump Case, #...

    Thanks, Mike!

    I'm looking for the Pump Case, # 59336-3713. This is the part that goes over the impeller. They get water in them and the liner separates from the housing.

    The expansion...
  23. I guess I don't understand. Your 'Ski isn't hard...

    I guess I don't understand. Your 'Ski isn't hard to maintain at all. It requires very little maintenance. We've tried to help, and you can find videos on most everything on YouTube. Oh, well...
    ...
  24. Replies
    11
    Views
    559

    I have NOT purchased from Megazip, they came up...

    I have NOT purchased from Megazip, they came up when I did a search for your part number. They have claimed to have some parts I've needed in the past, but pricing was slightly higher than other...
  25. Replies
    11
    Views
    559

    Welcome aboard, MadHatter! Megazip.net says...

    Welcome aboard, MadHatter!

    Megazip.net says they have it, but I don't see a phone number to confirm it. https://www.megazip.net/zapchasti-dlya/kawasaki/cap-110123772

    SBT carries some...
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4