Search

Type: Posts; User: SeawardToast

Page 1 of 4 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    13
    Views
    388

    Ah yes if you pulled the pump you are fine

    Ah yes if you pulled the pump you are fine
  2. Replies
    13
    Views
    388

    Awesome, looks great. Keep in mind the driveshaft...

    Awesome, looks great. Keep in mind the driveshaft will not go back in with the bearing holder bolted in, you have to slide it onto the driveshaft and then put it in pkalce.
  3. Replies
    9
    Views
    355

    Update from Robin. A little play in the motor...

    Update from Robin. A little play in the motor mounts is fine, according to him the 2 stroke skis don't like super stiff mounts. He also noted that the prop rattle was normal for kawasaki skis when...
  4. Replies
    13
    Views
    388

    Also, you don't absolutely need to pull the...

    Also, you don't absolutely need to pull the engine all the way out. I just lifted mine about 8 inches. I have replaced all the fuel and oil lines so I had enough length to do this. It may something...
  5. Replies
    9
    Views
    355

    Yes all the mounts are right, I did check that. I...

    Yes all the mounts are right, I did check that. I can pull the pump no issue but looking from the bottom through the ride plate the clearance looks good. When I had the pump out at the beginning of...
  6. Replies
    9
    Views
    355

    Before I ordered the mounts I asked, he said all...

    Before I ordered the mounts I asked, he said all mounts nowadays are made with the "race" spec. I will reach out tomorrow and ask his opinion. Thanks guys
  7. Replies
    9
    Views
    355

    Motor mount play

    Hey guys, so I've had the rhaas motor mounts on my stxr for a month or so now. I've noticed that it's pretty easy to "wiggle" the engine back due to the flex of the motor mounts. Is this normal? I...
  8. Replies
    13
    Views
    388

    Goodluck! Make sure you have the thru hull...

    Goodluck! Make sure you have the thru hull carrier in the correct position (I test fit it and marked on the hull with sharpie) before sealing it completely. Don't want your driveshaft to rub against...
  9. Replies
    2
    Views
    113

    Spark? Have you confirmed all cylinders are firing

    Spark? Have you confirmed all cylinders are firing
  10. Agree with Steve.. As excited as you may be to...

    Agree with Steve.. As excited as you may be to get out on the water to try and test you need to go over everything in the ski and make sure it is correct before going out. Negligence is only going to...
  11. Okay cool. Different style bar but the blowsion...

    Okay cool. Different style bar but the blowsion bars will still fit
  12. Great. I'll be picking up a set and do the...

    Great. I'll be picking up a set and do the bushings just for peace of mind
  13. Awesome, did you replace any other steering...

    Awesome, did you replace any other steering components when swapping them out?
  14. awesome thank you

    awesome thank you
  15. Best material to replace traction mats?

    The traction mats (not sure if that's the correct name) on my STXR have seen better days and are peeling off. Is there a material I can purchase in rolls and cut to size to replace the existing...
  16. Do you like the bars? How is the riding position...

    Do you like the bars? How is the riding position compared to stock
  17. Aftermarket handlebars / grips for STXR

    Hey guys, do any of you run aftermarket handlebars or grips on your skis? If so, which ones would you recommend for a 2002 STXR
  18. Replies
    44
    Views
    1,701

    So found the main source of my leak. I had...

    So found the main source of my leak. I had forgotten to tighten one of the hose clamps on the thru hull carrier rubber tube. I also will be applying silicon to the back of the driveshaft holder after...
  19. Replies
    44
    Views
    1,701

    I tried idling it with seat off and watching but...

    I tried idling it with seat off and watching but not actually riding it, I will give that a shot. Really hoping the thru hull carrier didn't come up somehow I put an enormous amount of 5200 on/under...
  20. Replies
    44
    Views
    1,701

    Fixed the hose inlet leak, still getting an...

    Fixed the hose inlet leak, still getting an abnormal amount of water in the hull. Was wide open for about 5-10 minutes and enough for a steady stream to come out both drain plugs after.i pulled it...
  21. Replies
    1
    Views
    212

    Cylinder and pisser water temp

    I am curious what the temps of the cylinder / exhaust / pisser water should be on the Kawasaki 1200 triple. I have the triple pisser mod and the water comes out hot but not scalding. The cylinders...
  22. Replies
    44
    Views
    1,701

    Update, I was correct about no spark but I...

    Update, I was correct about no spark but I overlooked a simple thing originally. Turns out it was a bad fuse causing my no-start. Swapped it out and the ski fired right up. Got out on the water...
  23. Replies
    44
    Views
    1,701

    I'm just guessing. I just feel confident that it...

    I'm just guessing. I just feel confident that it isn't fuel because it ran great before I pulled the engine to do the carrier. I'll have to check for spark to verify but that's my hunch
  24. Replies
    44
    Views
    1,701

    You know what I just remembered, when I was...

    You know what I just remembered, when I was testing the seal and filling hull with water the spark plug boots I accidentally forgot in the hull so they were fully submerged for probably 5 minutes....
  25. Replies
    44
    Views
    1,701

    Fixed the thru hull carrier and put everything...

    Fixed the thru hull carrier and put everything back together. Go to start it up and it doesn't start. What gives?? Motor turns over very strong and all fuel lines connected. This thing started 3 days...
Results 1 to 25 of 96
Page 1 of 4 1 2 3 4