Search

Page 1 of 2 1 2

Search: Search took 1.00 seconds.

  1. Replies
    260
    Views
    30,126

    23 only makes 23 no matter what rpm. the 56 mm...

    23 only makes 23 no matter what rpm. the 56 mm inlet of the housing prevents it from making more. BTW it will not make 23 psi (manifold pressure) until 9k+ rpm.
  2. Replies
    24
    Views
    3,609

    Maybe on a stock 300. Once you start to mod it...

    Maybe on a stock 300. Once you start to mod it and setup the correct 161 prop it will beat the 159 all over.
  3. There is no sc out there that will make enougg...

    There is no sc out there that will make enougg boost to blow the stock bottom. Its very strong. Holds 30 psi all day
  4. Yes you would run e85. No need to run c85 unless...

    Yes you would run e85. No need to run c85 unless pump e85 is not available by you
  5. Replies
    65
    Views
    7,221

    Maybe a little mis leading saying it a gtr. You...

    Maybe a little mis leading saying it a gtr. You left out the part that its a t3 bottom. No gtr bottom go that speed on 30 psi
  6. Replies
    50
    Views
    6,902

    There wasnt even lots of boats at whole event....

    There wasnt even lots of boats at whole event. What do you consider a ss boat in spec? Other then 1 boat with intake out side (which does nothing) i did not see that. Maybe your just not used to...
  7. Replies
    19
    Views
    4,891

    85 lbs fonal and stock gaskets are just fine....

    85 lbs fonal and stock gaskets are just fine. Have run plenty o engines 30lbs plus on it. 95lbs starts to squash head. You need to install inserts to stop that if u have to torque more. If ur poppinv...
  8. Replies
    21
    Views
    1,484

    You need to post a pic of the retainers for me to...

    I have torx racing springs and Ti retainers . So I be ok with these? Head is a brand new casting never been cut.[/QUOTE]

    You need to post a pic of the retainers for me to see. You may meed to...
  9. SOLD The first bosch ecu was 2009 on the 3 seaters....

    The first bosch ecu was 2009 on the 3 seaters. The first bosch ecu on 2 seater was with body change in 2012. A true seadoo enthusiast should know this.
  10. Replies
    119
    Views
    18,827

    Ginger colored underwear with your wifes name on...

    so if black vr knows so much... The 40 lb boost at 9900 rpm and 65 shot are incorrect?[/QUOTE]

    Well considering my name is brian k and i tune the ski. I would say yes i know more then even the...
  11. Thats not a 2016 ic. The new ic does not fit...

    Thats not a 2016 ic. The new ic does not fit above pump tunnel. Thats just a replacement ic for earlier models
  12. Thread: 27 cam?

    by blackvr
    Replies
    6
    Views
    672

    same thing. 27 is a good cam to regrind

    same thing. 27 is a good cam to regrind
  13. Replies
    147
    Views
    19,203

    i think if you had a jet pump and prop from a 260...

    i think if you had a jet pump and prop from a 260 then peoples thoughts will be different. remember there trying to keep the ski slow so basically they made the final drive longer. ski only targets...
  14. New engine runs no where near 18 psi. 18 psi on a...

    New engine runs no where near 18 psi. 18 psi on a 1630 engine will put u close to 400 hp. Just use common sense. old 1494 engine made 260 on 10 psi.
  15. Replies
    18
    Views
    3,078

    Single locks are good for high hp applications....

    Single locks are good for high hp applications. Not good for everday rider. Single locks dont allow valve to spin to keep the seat fresh. I have always had longevity issues with single lock valves...
  16. Replies
    18
    Views
    3,078

    Riva calls ferea riva branded valves. Why dont u...

    Riva calls ferea riva branded valves. Why dont u bitch bout them. Its a business thing. I would stay away from torx not because of wut they use but because of customer service. Yet buy a vipec from...
  17. Replies
    18
    Views
    3,078

    Torx used REV valves. You can contact REV direct....

    Torx used REV valves. You can contact REV direct. Www.revvalves.com they are very good valves. Supertech and rev come from argentina. Ferea is using china material now
  18. Thread: Turbo-Tastic

    by blackvr
    Replies
    128
    Views
    16,810

    You guys are funny. the turbo that he is using...

    You guys are funny. the turbo that he is using will no were near hit 40 psi. the exhaust housing he is running will not support it. If any of you new anything about reading compressor maps match with...
  19. Replies
    302
    Views
    26,138

    Nobody cares how much hp your computer says it...

    Nobody cares how much hp your computer says it will make. Sounds like a bunch of hoopla to me. Build it, and make it work. End results are all anyone cares about.
  20. Replies
    1,562
    Views
    188,057

    Why would u never go over 65psi pressure? And why...

    Why would u never go over 65psi pressure? And why would Gus need such a big injector? Kind of a waste since what he has now is working well
  21. Replies
    20
    Views
    2,056

    Forever :smt007

    Thats cause im to busy spending my money on gas to ride my ski. Something your not familiar with:p[/QUOTE]

    Guess you two are still dating.. :D[/QUOTE]
    Forever :smt007
  22. Replies
    20
    Views
    2,056

    Scott ur not serious? Look at his sig dumb ginger

    Scott ur not serious? Look at his sig dumb ginger
  23. Replies
    28
    Views
    3,555

    newer ibr nozzles are super weak. your best best...

    newer ibr nozzles are super weak. your best best is to find an older nozzle, cut all the ears off and it bolts right up. broke a couple when i was still sc. use an older one now and no problems at...
  24. Replies
    25
    Views
    1,816

    Thats awesome! That should help alot

    You wont be able to get the tune perfect with and torx cam and vtech tuner. there rpm map ends at 8600 and boost at 11 psi. Depending on boost your running now If you want a cheaper and faster way...
  25. Replies
    25
    Views
    1,816

    You wont be able to get the tune perfect with and...

    You wont be able to get the tune perfect with and torx cam and vtech tuner. there rpm map ends at 8600 and boost at 11 psi. Depending on boost your running now If you want a cheaper and faster way...
Results 1 to 25 of 46
Page 1 of 2 1 2