Search

Type: Posts; User: EVN81

Page 1 of 8 1 2 3 4

Search: Search took 0.01 seconds.

  1. View Post

    You can go with 3/4Ē outlet.
    The first T-piece should have an internal restriction towards inlet hose IC.
    Towards exhaust manifold is full bore.

    Pull hose to check because Ď16 / Ď17 models are...
  2. Replies
    7
    Views
    276

    DashFlash also offers the speed limiter removal

    DashFlash also offers the speed limiter removal
  3. Replies
    32
    Views
    2,800

    Not that easy, the culprit is you need the...

    Not that easy, the culprit is you need the alignment tools to do the job properly.

    Not just install all new (basically all IS new with all these low hours)
  4. Replies
    32
    Views
    2,800

    View Post

    0 Hours [emoji23]
    Iím not sure whatís off, engine or tru-hull....
    Also rubber flap is to short and not completely covering carbon ring.....
    449483
  5. Replies
    4
    Views
    230

    View Post

    Ah ok my bad, that I donít know!
  6. Replies
    20
    Views
    9,924

    +1 [emoji3]

    +1 [emoji3]
  7. Replies
    4
    Views
    230

    Yes it will fit. It gives more tension on the...

    Yes it will fit. It gives more tension on the bellow.

    You might have some installation issue due the hat touching the SC during the re- installation of SC.
    I assume you take SC out to have more...
  8. https://brpmanuals.com/seadoo-manual.htm ...

    https://brpmanuals.com/seadoo-manual.htm

    Scroll down for 2008
    $ 9.50
    You get the manual as PDF file without any restrictions!
  9. Thread: IBR fault code

    by EVN81
    Replies
    11
    Views
    433

    Serious does anybody read the owners...

    Serious does anybody read the owners manual.........?

    Page 111 (for RXP)
  10. Replies
    8
    Views
    617

    View Post

    Iím not doubting the knowledge of Mr. Jesus. He has probably far more tuning knowledge then 95% of this forum together.

    Iím just sharing my experience.
    I found my log from that run with stock...
  11. Replies
    8
    Views
    617

    You can invest in an separate A/F gauge or...

    You can invest in an separate A/F gauge or DashPac module for A/F.
    For a piece of mind whatís going on under the seat while riding.
    And do not have to thrust blind on other peoples experiences.
    ...
  12. Replies
    8
    Views
    617

    Need some help/advice

    From my experience I can tell you no!
    I ran with stock injectors max 8340 and when I checked log the injector duty cycle was showing 105%.
    Luckily I only made one pass!
    So you know what that...
  13. Replies
    7
    Views
    375

    So with spark plugs removed you can spin...

    So with spark plugs removed you can spin driveshaft easy?
    But engine will still not turn?

    I would think broken driveshaft at engine side. Remove driveshaft to verify.
    Possible this happened when...
  14. Replies
    2
    Views
    289

    FS - Parts ttt

    ttt
  15. Well.... NOT on NGK plugs! ...

    Well.... NOT on NGK plugs!

    http://b2600i.com/images/ngk_tb_0630111_antisieze.pdf

    http://greenhulk.net/forums/attachment.php?attachmentid=448847&stc=1
  16. Replies
    14
    Views
    1,795

    Keep in mind that older models had the brass nut...

    Keep in mind that older models had the brass nut molded in plastic.
    Very prone to strip, as said no Loctite and just hand snug!
    And weíre talking here about the 1st gen iBr and only the bolts...
  17. Replies
    9
    Views
    366

    Beside this (which is probably the cause), only...

    Beside this (which is probably the cause),
    only other reason can be that the oil seal / bearing assembly is not properly pulled back after assembly or repair.
    The Ďtell taleí line should be visible...
  18. Replies
    9
    Views
    387

    View Post

    Iím located in Europe and not home for the coming 2 weeks. Otherwise I could you send it to you.
    Have a look here:

    http://partsfinder.onlinemicrofiche.com/4tec/showmodel.asp?make=seadoopwc
  19. Partly, see the FB site from GRF for info about...

    Partly, see the FB site from GRF for info about 2019 digital cluster.
  20. Replies
    9
    Views
    387

    What hoses should go here?!?!

    No itís not. The hose you see is the incoming cooling line from jetpump. It passes through a cap on the iBr actuator where the temp. sensor sits and from there it splits in 2 to IC and exhaust...
  21. Replies
    8
    Views
    302

    View Post

    Iím very often on open sea and sometimes alone but I ALWAYS carry a PLB with me.
    I would advice that to every serious open water rider!

    https://www.acrartex.com/products/resqlink-plb
  22. Dashflash offers a speedlimiter override, similar...

    Dashflash offers a speedlimiter override, similar as the SCOM but here itís in the flash of cluster.
    Although not very clear itís shown in their YouTube vids.
  23. Replies
    9
    Views
    387

    What hoses should go here?!?!

    There you should be your bailer hoses connected.
    For sure youíll taking in water.
    And one connection is even broken.
    You need to replace that part.

    Or (this is not very good advice) block the...
  24. I always clean the old Loctite out with a tap or...

    I always clean the old Loctite out with a tap or bolt with a vertical cut.
    Too easy to damage the alu threads.

    I use Loctite 243 blue on those venturi bolts after I lost one once.
    Luckily...
  25. Replies
    9
    Views
    477

    As suggested an Y would flow even better. But...

    As suggested an Y would flow even better.

    But again be carefull not starve water to exhaust system.
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4