Search

Type: Posts; User: stimpsonjcat

Page 1 of 8 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    3
    Views
    61

    I think I am going to finish getting the 4th ski...

    I think I am going to finish getting the 4th ski built and into the water and then yank the one with the starter issue.

    I looked and a freaking limb has broken one of the runners on my only empty...
  2. Replies
    3
    Views
    61

    I think my bendix is busted...

    Ski was running fine just a few weeks ago, now it just spins the starter motor.

    I'll put a charger on the battery tomorrow am and let that sit a while and try it again.

    I am able to spin the...
  3. Mine either pop (and bleed fast) or just start to...

    Mine either pop (and bleed fast) or just start to bleed down at the specified pressure.
  4. Replies
    14
    Views
    403

    It's all good mate, every time I get it right...

    It's all good mate, every time I get it right here I feel justified for all the questions I have asked her.
  5. That battery mounted setup is death waiting to...

    That battery mounted setup is death waiting to happen.

    My SLX had that setup and the CDI coming loose jumping waves was what killed it.
  6. Replies
    14
    Views
    403

    What are you referring to here, mate? manual...

    What are you referring to here, mate?


    manual says:
    "NOTE: 1995 and later models are equipped with a variableoil pump controlled by a link rod between the carburetors
    and the pump arm. This is...
  7. Replies
    5
    Views
    201

    I will mirror xlint89, I built one from a...

    I will mirror xlint89, I built one from a complete wreck, including major fiberglass work to the hull, and in the end I parted it and put the engine in an SLT780 hull.

    It was huge fun on flat...
  8. Replies
    14
    Views
    403

    I like the Polaris oil system, just be sure your...

    I like the Polaris oil system, just be sure your hoses for that are good.

    Is the engine out of the ski? If so I recommend a full tear down to check the crank for issues, but it's your...
  9. Replies
    4
    Views
    226

    MFD is functional and connected? Any blinking...

    MFD is functional and connected? Any blinking lights or warnings there?

    Vapor lock? Easy to test just crack the fueling cap.

    Does it come out of the hole OK and just not top end? points to...
  10. Replies
    13
    Views
    842

    Tear down vid: https://youtu.be/lRtShWdJHfk...

    Tear down vid:


    https://youtu.be/lRtShWdJHfk


    Rebuild pt 1:


    https://youtu.be/z2Zj-xcA4nQ
  11. Replies
    13
    Views
    842

    OK, so, in April I bought a core exchange crank...

    OK, so, in April I bought a core exchange crank and (3) cylinders on a core swap from SBT.

    When I filmed my unboxing vid for those parts and posted it I won $500 worth of credit which I...
  12. Replies
    13
    Views
    842

    I will try that as I have a stock cylinder handy.

    I will try that as I have a stock cylinder handy.
  13. Replies
    13
    Views
    842

    I checked with SBT and they want everything back....

    I checked with SBT and they want everything back.

    Looking at my pic and their website, sure looks like the correct ring part # to me, which probably means the cylinders are bored more than 0.5...
  14. Replies
    13
    Views
    842

    I sent them an email and will call Tuesday. 5x...

    I sent them an email and will call Tuesday.

    5x the nominal gap got my attention.
  15. Replies
    13
    Views
    842

    Well, was checking gap on the cylinders and...

    Well, was checking gap on the cylinders and pistons/rings I got from SBT and ring gap is 0.075"?!?!

    https://www.dropbox.com/s/h1m5zbtwtj97odo/pistonringsmall.jpg?raw=1

    Vert da ferk?
  16. xlint nailed it IMHO. Have you checked the...

    xlint nailed it IMHO.

    Have you checked the wear in the cylinder? I was surprised how badly belled even good-looking cylinders can be.
  17. Replies
    6
    Views
    314

    Yeah, they are getting hard to find. I have a...

    Yeah, they are getting hard to find. I have a 780 with most cables bound up I am hoping I can resurrect the MFD off of.

    I have a backup plan to use a small PLC or an arduino if all my MFDs...
  18. Wiring diagrams are on the spec page:...

    Wiring diagrams are on the spec page:
    https://cdn.automationdirect.com/static/specs/proxlpcaprectangle.pdf

    The 'load', in this case the relay coil, can be between +12V and the signal wire or it...
  19. The relay pulls about 60mA of current steady...

    The relay pulls about 60mA of current steady state. It's only the inrush that is a waste.

    The sensor can be wired PNP or NPN.
  20. Dead gas level sender and don't want to rip the tank out to replace? My alternative

    So I have TWO skis where the sending unit in the gas tank has died.

    Mind you, I have plenty of spare senders.

    But I do not relish the idea of getting the tanks out just so I can replace the...
  21. Got the leak sorted. Turns out I had TWO. ...

    Got the leak sorted.

    Turns out I had TWO.

    One was where the cooling tube came through. I added an O-ring to the outboard side, put some silicone on it, passed it through, assembled the pump to...
  22. Hmmm...how to seal the engine cooling water supply tube on the hull side?

    I don't recall this ever being an issue on my other skis, but on this hull the fitting in the pump where it goes through the hull is not tight and is leaking slightly. It's no big deal out and about...
  23. What's a ramp? My skis stay on the dock unless...

    What's a ramp?

    My skis stay on the dock unless they need surgery.
  24. Replies
    6
    Views
    314

    I like it. Where's your MFD?

    I like it.

    Where's your MFD?
  25. Replies
    6
    Views
    269

    Yep, I drill all the jets one size over on any...

    Yep, I drill all the jets one size over on any carbs I rebuild now. Easier to screw them in than have them tuned but about to fall out.
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4