Search

Type: Posts; User: wrenchin510

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. Replies
    29
    Views
    2,003

    I bit the bullet and pulled the engine out of...

    I bit the bullet and pulled the engine out of this ski. I pulled the starter, and Bendix. I bench tested the starter, it’s working fine. The Bendix gear seemed to be binding and not engaging the...
  2. Replies
    29
    Views
    2,003

    View Post

    I don’t knowing I understand. Are you saying to use a desperate power supply. Which I have it’s a 30v10amp adjustable one. And splice into the EMM to power it? Then check the TPS? Where would I...
  3. Replies
    29
    Views
    2,003

    View Post

    Here’s my current condition. The ski won’t start. I recorded it and posted it to YouTube. I hooked up the TPS to a volt meter.

    Anyone have any input?

    https://youtu.be/b1iBtGsiOVo
  4. Replies
    29
    Views
    2,003

    I had them hooked up backwards on the water....

    I had them hooked up backwards on the water. Hmmmm, could this have cause a “bogging” condition? At least attributed to it...
  5. Replies
    29
    Views
    2,003

    I noticed this picture before I disassembled and...

    I noticed this picture before I disassembled and rebuilt the fuel lines. Does it really matter which line is connected to supply, or return? I have the “TOP” line connected to the Supply side of the...
  6. Replies
    29
    Views
    2,003

    View Post

    I am not sure if it’s OEM Stock, this ski has what looks to be an original 2002 computer.
    Here is what is in there.

    437772
    437773
  7. Replies
    29
    Views
    2,003

    Yes, this is very similar to what was happening...

    Yes, this is very similar to what was happening in the water. Ide actually have to bump the start button to get it started. If I held he button down, I would hear the motor building pressure like...
  8. Replies
    29
    Views
    2,003

    It may be the Bendix on the starter spinning....

    It may be the Bendix on the starter spinning. Once I let go of the button, I hear like a hard stop of the I assume the bendix as well.
  9. Replies
    29
    Views
    2,003

    Got the OTC Gauge. 150psi across all 3 cylinders....

    Got the OTC Gauge. 150psi across all 3 cylinders. I took the Genesis out this past weekend for the first time since the rebuild. Still have a bogging condition. I’m pointing at the EMM, fuel pressure...
  10. Replies
    9
    Views
    988

    That looks like it would work. I reviewed the...

    That looks like it would work. I reviewed the service manual today. It makes mention of the “bleed screw” and “Bleeding Procedure” but doesn’t illustrate or explain how to execute. There are 3 places...
  11. Replies
    9
    Views
    988

    Would you happen to know how to bleed the oil...

    Would you happen to know how to bleed the oil lines using the bleed screw? I’m not sure I understand the attachment your talking about? Any photos of it?
  12. Replies
    50
    Views
    2,700

    View Post

    Finally got my ski back together. It’s been a while, will try and fire it up tomorrow!
  13. Replies
    9
    Views
    988

    View Post

    I finally got my motor put back into my ski. It’s a 02 Polaris Genesis I DI Model. Haven’t fired it yet, should I premix my fuel 40:1 and bleed the oil lines. I was looking at the oil mech, where is...
  14. Replies
    29
    Views
    2,003

    I ordered an OTC gauge.

    I ordered an OTC gauge.
  15. Replies
    29
    Views
    2,003

    Update: I just did a full top end rebuild on this...

    Update: I just did a full top end rebuild on this ski, it fires with a little throttle, it'll stay running once you open the throttle a few times and rev it. But, after I had it run for about 15...
  16. Replies
    19
    Views
    1,252

    Where did you find the magnet to replace the...

    Where did you find the magnet to replace the broken one?
  17. Replies
    50
    Views
    2,700

    Thanks for the info guys!

    Thanks for the info guys!
  18. Replies
    50
    Views
    2,700

    Just ordered 2! Thanks How are you able to tell...

    Just ordered 2! Thanks
    How are you able to tell if the oil pump is working? I would think you all have come up with some sort of test..
    I've been reading through the forum, and can seem to find a...
  19. Replies
    50
    Views
    2,700

    Will review the Hose Barb Method and get that...

    Will review the Hose Barb Method and get that done.
    I found something that was concerning.
    When I was cleaning the hull, getting it ready for the engine to go back in. I took a look at the oil...
  20. Replies
    50
    Views
    2,700

    Just emptied the tank and wiped it out! Then...

    Just emptied the tank and wiped it out!
    Then cleaned the fuel pump and fuel filter.
    Fuel Pressure Regulator is intact with oetiker clamps.

    418628418629418630418631
  21. Replies
    29
    Views
    2,003

    Spark Plugs: 418626

    Spark Plugs:
    418626
  22. Replies
    29
    Views
    2,003

    I just re-checked the Compression Mag-418623...

    I just re-checked the Compression
    Mag-418623
    Center-418624
    PTO-418622[/ATTACH

    Spark Plugs
    [ATTACH]418625
  23. Replies
    29
    Views
    2,003

    Just did a fuel pressure test, 20psi at the...

    Just did a fuel pressure test, 20psi at the shrader valve.
    Removed the fuel pump/canister, and cleaned the filter with a combo of compressed air and Gumout Carb/Choke Cleaner. The Fuel Pressure...
  24. Replies
    50
    Views
    2,700

    Accidentally cracked the case...would it take a...

    Accidentally cracked the case...would it take a weld?
    418617418618
  25. Replies
    29
    Views
    2,003

    2002 Polaris Bogging Down

    Lost a lot of power on the last time out. Bogged down, and wouldn't go above 3000RPM
    418615
    418616
Results 1 to 25 of 57
Page 1 of 3 1 2 3