Search

Type: Posts; User: kartracer

Page 1 of 6 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    11
    Views
    1,777

    So much for that dealer,they couldn't find a...

    So much for that dealer,they couldn't find a missing a missing intake grate??????????
  2. carbs.

    you may have a set of carbs. that aren't in the best of condition,as far as the hesitation goes.a different set may work better.With that said i have just what you need.LOL:lol:
  3. after thinking about it, I agree with this.

    after thinking about it, I agree with this.
  4. pretty sure when they say "Y lead" they mean the...

    pretty sure when they say "Y lead" they mean the lead with yellow wires,the rubber around the connecters are there to protect them from touching a power source & shorting something out & for a few...
  5. I do it with the plugs out,for no other reason...

    I do it with the plugs out,for no other reason then there coming out anyway & well for whatever its worth,it is easier on the starter,im only looking for a bad cylinder or maybe one below 100psi. ...
  6. I don't understand why you wouldn't have adjusted...

    I don't understand why you wouldn't have adjusted the TPS before you started the engine, you have everything to do it????
  7. np, lets hope your engine stay together so im not...

    np, lets hope your engine stay together so im not sending you one as a bonus. lol
  8. I don't see the three bond staying in place,the...

    I don't see the three bond staying in place,the gas will lift it off once it gets saturated,it may not hurt anything if it goes through the engine,but whats the point of it even being there.I went to...
  9. so every time you pull a pump from a ski there...

    so every time you pull a pump from a ski there will be three shims????? for someone that has not or does not care to mess with shimming,groupk will do it all & all you do is put it in,seems pretty...
  10. one more thing group K will do,is make sure your...

    one more thing group K will do,is make sure your new prop is the right pitch,theres a write up where they were doing testing with two same ski's that happen to be ultra's or stxr's, one was slower,...
  11. with the ultra pump the wearing has a taper,i...

    with the ultra pump the wearing has a taper,i guess some times theres more clearance on one side of it,so they shim it up to even it out,they say theres a difference,but idk. if there gonna rebuild...
  12. YEP

    YEP
  13. that would be to simple?????????

    that would be to simple?????????
  14. is it me or is there some kind of paint flaking...

    is it me or is there some kind of paint flaking off in the intake.
  15. not sure why your torqueing the studs down,clean...

    not sure why your torqueing the studs down,clean them, put alittle Loctite & run them down until they stop,done,what r u doing putting two nuts together & torqueing them down??its cracked on both...
  16. for what its worth he told you a lot of bull shit...

    for what its worth he told you a lot of bull shit to.have you forgot that already.
  17. 223 hours, 17 years old.but it can't be crank...

    223 hours, 17 years old.but it can't be crank seals?????
  18. I would think you would lose a cylinder firing if...

    I would think you would lose a cylinder firing if your fuel pump was just weak enough to do what your thinking,it takes 15 psi to open the NS so if your pump wasn't keeping up the pressure would drop...
  19. Hey Hey Hey, he's not pulling chit out,give it a...

    Hey Hey Hey, he's not pulling chit out,give it a rest,not until it sinks.
  20. Well group k has a big bold phone number you can...

    Well group k has a big bold phone number you can call like us old school boys use to do,i know it sounds strange,but it works,200.00 will get your pump rebuilt without a upgrade to the impellor.
  21. WoW I just sold a mint display for 200.0 with two...

    WoW I just sold a mint display for 200.0 with two Orange keys & Orange switch.
  22. I'm thinking I told you to snug those six nuts...

    I'm thinking I told you to snug those six nuts alittle before you tighten up the base nuts for the cylinders,it helps alittle to get the cylinders aligned,did you try to tighten the outside alittle...
  23. put some soapy water in a spray bottle & find the...

    put some soapy water in a spray bottle & find the leak.
  24. all this is way over the top for me.

    all this is way over the top for me.
  25. what about the brass fitting in the upper left on...

    what about the brass fitting in the upper left on the pipe???
Results 1 to 25 of 135
Page 1 of 6 1 2 3 4