Search

Type: Posts; User: AsianToo

Search: Search took 0.00 seconds.

  1. Yeah, kinda what I was thinking. I wish shipping...

    Yeah, kinda what I was thinking. I wish shipping was cheaper to Australia !!
  2. Current market prices for used '99 performance parts

    I'm at a point where toys and life are crashing together. I need some help - I'm thinking of either selling my '99 GP 1200 r3 or parting it out. I haven't seen a lot of performance parts for sale, so...
  3. Replies
    8
    Views
    495

    They are just castings...... did you try a...

    They are just castings...... did you try a straight edge to see if they're actually flat? Or is there a weaker spot(less supported) on the body at that corner that distorts under load. OR... leave...
  4. Replies
    3
    Views
    527

    before you replace your starter, make sure all...

    before you replace your starter, make sure all your cables are good and all connections are recently cleaned(wire brushed). There's no load on the starter in the water, bc it's not moving the prop...
  5. Replies
    3
    Views
    527

    carbs. Take the diaphragm covers off and clean or...

    carbs. Take the diaphragm covers off and clean or replace them. I put a little grease on them so they don't stick to the cover. The diaphragm allows the fuel to get to the main jet and make rpm and...
  6. Replies
    2
    Views
    341

    Try looking at your carb diaphragms. Pull the...

    Try looking at your carb diaphragms. Pull the covers and make sure they're not cracked, stiff or stuck to the cover. The carbs work by load or vacuum, then pulling the diaphragm into the carb opening...
  7. Replies
    26
    Views
    2,971

    Wow, your ski is so damn clean! Glad to hear it's...

    Wow, your ski is so damn clean! Glad to hear it's running well. I've got my '99 Riva r3 going but I've been trying to solve a bad porposing problem. I've got it to settle down to about 50, but after...
  8. Replies
    3
    Views
    315

    I used a '94 with a 701 as a donor for my boat....

    I used a '94 with a 701 as a donor for my boat. It was sitting for nine years, all I had to do with the motor was clean up the carbs. The diaphragms were hard as glass and stuck to the covers. I went...
  9. Sticky: Keep posting your insights - they are needed....

    Keep posting your insights - they are needed. Everyone is welcome to post their knowledge and it may be just what someone else is looking for. Keep the butt-hurt feelings for instagram or twitter and...
  10. Sticky: Dude - Don't they have an app you can tell this...

    Dude - Don't they have an app you can tell this to? I was fine with just reading your comments and going on with whatever I wanted to take from it - that's what a forum is for. As for your opinion on...
  11. Sticky: "Its as though I am debating a elementary school...

    "Its as though I am debating a elementary school person who resorts to using his buddies to prove an agenda or a 90 year who cannot comprehend or accept what is common knowledge."

    " Cause your...
  12. Replies
    6
    Views
    534

    what's the hull look like in front of the pump?

    what's the hull look like in front of the pump?
  13. FS Did you ever sell this ski? Do you know where it...

    Did you ever sell this ski? Do you know where it ended up?
  14. Replies
    21
    Views
    2,333

    Thanks - I've got a quick question for you, I've...

    Thanks - I've got a quick question for you, I've been around the site and reading a bunch - What do they mean when they say "factory pipes"? I was under the impression that Riva made them. I'm...
  15. Replies
    21
    Views
    2,333

    442500

    442500
  16. Replies
    21
    Views
    2,333

    442497442498442499

    442497442498442499
  17. Replies
    21
    Views
    2,333

    Trying to load some pics. I'll figure it out at...

    Trying to load some pics. I'll figure it out at some point!
  18. Replies
    21
    Views
    2,333

    442496

    442496
  19. Replies
    21
    Views
    2,333

    I found out I have a Riva plate with no shims. I...

    I found out I have a Riva plate with no shims. I found a stock ride plate and I put 4 ss washers on the back bolts - about 0.160". I'll put a digital level on it before I get back out.
  20. Replies
    21
    Views
    2,333

    Quick update - put it in the lake today. Water...

    Quick update - put it in the lake today. Water was flat as glass - I got it up to half throttle before it was porposing really bad. Cavitating at each hop(55 on GPS) full throttle it wanted to jump...
  21. Replies
    21
    Views
    2,333

    Got it fired up today. All seems good. I'll try...

    Got it fired up today. All seems good. I'll try to wet test it this week. May go to the river this wknd and get some time on it. I'll post a top speed if I go out.
  22. Replies
    21
    Views
    2,333

    I did some work on the ski and found out some of...

    I did some work on the ski and found out some of the parts on it. It has "Buckshot" carbs with an R&D manifold. Block has been ported and epoxy coated. It has a billet head and Riva triple pipes. I'd...
  23. Replies
    21
    Views
    2,333

    How about anything and everything. My only time...

    How about anything and everything. My only time with skis in general is getting my 96 running and cutting my 94 and making my YouTube jet boat. Generally, what should I be concerned about pre wet...
  24. Replies
    21
    Views
    2,333

    Trying to find info on a 1999 Riva GP 1200R3

    Hi everyone - I'm new here and I'm hoping some of you used to race the gp1200. I just got a 99 gp1200 r3 and I'm wondering if anyone here has owned one, or has some background info on it. For '99...
Results 1 to 24 of 24