Search

Type: Posts; User: martincom

Page 1 of 8 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    15
    Views
    617

    From what I understand, the MSX140 EMMs were...

    From what I understand, the MSX140 EMMs were later in production and had better electrolytics. Some of the other issues would typically surface by now, if they were going to happen. So, if it ain't...
  2. Replies
    15
    Views
    617

    You are certainly entitled to your opinion. I...

    You are certainly entitled to your opinion. I stated "likely". My 40+ years of electronic component servicing has commonly seen electronic equipment remain in reliable service for far greater spans...
  3. Replies
    15
    Views
    617

    I disagree. The EMM can and likely will have age...

    I disagree. The EMM can and likely will have age related issues--nothing that cannot be repaired affordably and will likely be trouble free for another 20 years. Carburetors are perpetually...
  4. Replies
    15
    Views
    617

    Be sure to reinforce the fuel pressure regulator...

    Be sure to reinforce the fuel pressure regulator (FPR). It is known for literally falling off, inside the fuel tank. When this occurs, fuel pressure drops to near zero and the mixture becomes quite...
  5. Sticky: It would seem very odd and an extreme coincidence...

    It would seem very odd and an extreme coincidence that you would have two defective "paddle wheel" sensors. Not to insult your intelligence, but does your ohm meter read zero or near zero ohms when...
  6. To verify the injectors are on the correct...

    To verify the injectors are on the correct cylinder, you would only require DW, not a QR code reader. The injectors have S/N on their labels which are also displayed in DW. The only instance a QR...
  7. bspanovic is the other Australian member. I...

    bspanovic is the other Australian member. I believe he resides in Sydney. I don't know if that is close or not.
  8. swan is a member in Australia and I'm pretty sure...

    swan is a member in Australia and I'm pretty sure he has DW. I do't know what part of the country he resides within. He's a great guy. Utilize the forum's private message to reach out to him

    We...
  9. He indicated he was from Australia. We have a...

    He indicated he was from Australia. We have a few members there who have Digital Wrench (DW), the diagnostic software. With that and a cell phone QR code reader, you can determine if the injectors...
  10. Sticky: Yes, I suggested it and provided the bill of...

    Yes, I suggested it and provided the bill of materials to a member who had broke off the return line hose barb from the nylon head piece, last summer.

    I've also encountered a near identical...
  11. Sticky: It's more of a yellow. It is Valvoline X-All...

    It's more of a yellow. It is Valvoline X-All grease. I apply a coat to the hose barb to aide with seating the hose. It is especially helpful when installing 1/4" hose on a 5/16" barb---which also...
  12. Sticky: Alternative Direct Injection Fuel Pressure Regulator Reinforcement

    I've been working on my 2020/2021 winter project PWC, a 2003 Virage i. Upon removing the fuel canister and visually inspecting the fuel pressure regulator (FPR), I thought I had received a "free...
  13. See post #3 of this thread for the link.

    See post #3 of this thread for the link.
  14. SOLD WTB: Cylinder for a Polaris 800 Direct Injected/Virage i

    I have a project Virage i that has a crack in the cylinder casting along the mold line, from top to bottom. I'm seeking a serviceable replacement.

    No good deed goes unpunished. I had a complete...
  15. Replies
    9
    Views
    285

    C43 replacement: ...

    C43 replacement:

    https://www.digikey.com/en/products/detail/vishay-bc-components/MKP1839468084HQ/2260510
  16. I should be able to supply that. $20 shipped. ...

    I should be able to supply that. $20 shipped. If you're interested, PM me and also let me know which color you need, black or creme.
  17. PNs forthe fuel line and clamps. Link to the...

    PNs forthe fuel line and clamps. Link to the fuel line source.
  18. Replies
    33
    Views
    4,290

    Could be contaminated fuel. See this thread....

    Could be contaminated fuel. See this thread.
  19. Here is what you need for hose and clamps. I...

    Here is what you need for hose and clamps. I just copied it from another thread. Maybe k447 would include it in his info pages as I've sent it a number of times to various members:

    You'll also...
  20. I've never had an issue with them, but I don't...

    I've never had an issue with them, but I don't twist or pull on the hose to remove it. I remove the injector retainer bracket and then pull the barb fitting from the injector. I lay the...
  21. The link is in post #3 of this thread.

    The link is in post #3 of this thread.
  22. Replies
    3
    Views
    195

    WTB - Parts I'll sell the seat for $450 and drop it off at...

    I'll sell the seat for $450 and drop it off at the local UPS Store. Once I deliver it to the store, its yours. Here is a link to their web page if you want to contact them about shipping.

    It is...
  23. WTB - Parts PM sent.

    PM sent.
  24. Replies
    3
    Views
    195

    WTB - Parts I have a new one, in the wrapper. The shipping...

    I have a new one, in the wrapper. The shipping would surely be a deal killer. I've done two re-upholsters with the Hydro-Turf seat covers and have been pleased with the results. That being said,...
  25. Replies
    8
    Views
    449

    You are correct. I had Virage on the brain.

    You are correct. I had Virage on the brain.
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4