Search

Page 1 of 6 1 2 3 4

Search: Search took 1.00 seconds.

  1. After I installed my Y1000 I talked to Dean, he...

    After I installed my Y1000 I talked to Dean, he informed me that an additional reflash of my ECU was required to take into account the additional airflow of the Fizzle. So the lean condition is well...
  2. Replies
    2
    Views
    257

    WFO has those reeds, cages, and the plate. Shoot...

    WFO has those reeds, cages, and the plate. Shoot him a message.
  3. Replies
    9
    Views
    727

    Just get some 10x1.25 metric threaded rod. You...

    Just get some 10x1.25 metric threaded rod. You need enough for 12 pieces, bevel both ends of each piece. The length required includes 2 nut heights, plus 2 threads. Or, install one rod in the...
  4. Replies
    33
    Views
    2,166

    Saw your previous post about reusing the seals...

    Saw your previous post about reusing the seals and crank. If there is ANY doubt that a crank bearing is bad....have the crank repaired or replaced. And.....NEVER, EVER reuse crank seals on an...
  5. Replies
    33
    Views
    2,166

    Talk to Jeff at Competitive Crankshaft. He...

    Talk to Jeff at Competitive Crankshaft. He rebuilds cranks and is very competitively priced. I'm shipping a crank to them in the next few days for rephasing.
  6. Replies
    33
    Views
    2,166

    Remiving the flywheel is pretty straight forward,...

    Remiving the flywheel is pretty straight forward, even with the crank out. The coupler.....not quite as easy. The coupler should always be removed before the engine is torn apart. It is a standard...
  7. Replies
    33
    Views
    2,166

    Looked back and saw your spark plug thread, and...

    Looked back and saw your spark plug thread, and now the failure makes a little more sense. The #2 piston almost certainly failed due to water ingress. I've got a 1200r I'm working on now, and the...
  8. Replies
    4
    Views
    482

    1 and 3 look lean, almost excessively so, 2 looks...

    1 and 3 look lean, almost excessively so, 2 looks like it has a water ingestion problem, it looks steam cleaned.
  9. Replies
    33
    Views
    2,166

    Those are definitely nikasil cylinders. Also...1...

    Those are definitely nikasil cylinders. Also...1 and 3 look very lean, I would check and clean the fuel injectors also. Cylinder 2 could also possibly be a lean failure, its hard to tell. Ive seen...
  10. I'm in the same spot....but on the other side. I...

    I'm in the same spot....but on the other side. I have a '16 FXCSVHO I'm considering selling if I can get my heart right on it. If I do sell, I personally will give the buyer the choice of writing...
  11. You have to drill out the high and low speed...

    You have to drill out the high and low speed limiter caps. All you need to know is in the Yamaha how to section.
  12. Replies
    9
    Views
    769

    I have a good core crank. Whats it worth?

    I have a good core crank. Whats it worth?
  13. Replies
    7
    Views
    470

    Really hard to install the head gasket on...

    Really hard to install the head gasket on backwards. What about the base gaskets? Are the tabs to the exhaust side? If those are backwards it will definitely get water in the cylinders.
  14. Did you remove the limiter caps? If not, they...

    Did you remove the limiter caps? If not, they need to be removed so you can gain access to the screws. Correct spring for the carbs if you're NOT rejetting is the 115 gr spring. Not sure what...
  15. Those washers and springs freezing to the shaft...

    Those washers and springs freezing to the shaft are normal on those carbs. Very important....DO NOT RIDE THIS SKI UNTIL YOU HAVE OVERHAULED THE CARBS!!!!!! READ THAT AGAIN!!!!! That engine is...
  16. You can clean the cylinder wall with muriatic...

    You can clean the cylinder wall with muriatic acid to remove the aluminum sticking to the cylinder, if its a plated cylinder.
  17. I know you resolved your problem, but for those...

    I know you resolved your problem, but for those that do not know...every Yamaha that rolls off the line should be leak tested. Testing is simple, and unless you fill the ski completely, will not do...
  18. Replies
    24
    Views
    3,195

    Reviving an old thread....I recently rebuilt a...

    Reviving an old thread....I recently rebuilt a 66V for a customer who blew his engine. I previously owned the ski a few years ago, and was doing him a favor on the cheap. While I had the cases...
  19. Replies
    12
    Views
    1,138

    I run OSB's recipe for chokes intact, and mine...

    I run OSB's recipe for chokes intact, and mine runs perfect and starts easily. I have a ton of hours on mine. I also just built a 1200 PV motor for a customer and rebuilt his carbs to the OSB...
  20. I've run my GPR with and without socks. TBH I...

    I've run my GPR with and without socks. TBH I couldn't tell any appreciable difference. I run my highs and lows at the recipe +1/4 turn open. Works very well here close to sea level.
  21. Replies
    33
    Views
    4,285

    Those that knew Tommy and Barry had their lives...

    Those that knew Tommy and Barry had their lives enriched just by knowing them. It was my true pleasure knowing them. Barry has been gone a couple of years. ..and I still can't bear the thought of...
  22. Replies
    33
    Views
    4,285

    I missed this thread and made another when his...

    I missed this thread and made another when his wife texted me the news. Tommy Jordan and Barry Lee helped me out tremendously over the past few years. Actually met Tommy through Barry. For all of...
  23. Replies
    4
    Views
    825

    I didn't know...I've been off the forum a while...

    I didn't know...I've been off the forum a while pursuing my new motorcycle hobby. Tommy was a true gentleman, he will be truly missed.
  24. Replies
    7
    Views
    1,117

    I'd say a new clutch is in your future.

    I'd say a new clutch is in your future.
  25. Looks to be an aftermarket Riva stinger pipe. I...

    Looks to be an aftermarket Riva stinger pipe. I guarantee you Riva will not have any info on it anymore.
Results 1 to 25 of 146
Page 1 of 6 1 2 3 4