Search

Type: Posts; User: BlueFishCrisis

Page 1 of 8 1 2 3 4

Search: Search took 0.06 seconds.

  1. Replies
    15
    Views
    1,698

    Fuji Mounts, so should cram into 94-97 SLs and...

    Fuji Mounts, so should cram into 94-97 SLs and SLTs. See my build here: http://greenhulk.net/forums/showthread.php?t=223430
  2. Once you separate from the hull, you will then...

    Once you separate from the hull, you will then need to pull the pump along with the driveshaft free. It may also stick in there so don't get discouraged there as well.
  3. It is just a matter of removing the ride plate...

    It is just a matter of removing the ride plate and the 4 nuts from inside the hull. The pump will be very well stuck to the hull with factory silicone/adhesive.

    You also need to disconnect the...
  4. Haha both years.

    Haha both years.
  5. Replies
    11
    Views
    367

    Was trying to figure out what was going on with...

    Was trying to figure out what was going on with the water rail then realized it was a drive shaft. Shut off and water separator are not connected either.... Is this a work in progress photo?
  6. Replies
    3
    Views
    214

    If a problem arises after performing work, I...

    If a problem arises after performing work, I would be suspect of the reinstallation that took place. It is possible that air is entering the tunnel from around the through hull that was reinstalled...
  7. With it running well early, then lagging like in...

    With it running well early, then lagging like in the video sounds like magneto to me. Almost feels/sounds like a limiter type action. Everything else, of course, is worth looking at.
  8. Replies
    6
    Views
    356

    You will need to post a picture a little further...

    You will need to post a picture a little further back to see the whole box. That isn't a polaris OEM part so not sure what the connections should be.

    Where are you located?
  9. Replies
    4
    Views
    206

    5700 is high. I would expect a slight change...

    5700 is high. I would expect a slight change with the pump installed but not much. The Fuji motors usually idle around 3700 rpm out of the water. I would just adjust the throttle speed screw down...
  10. Replies
    9
    Views
    2,119

    FS - Parts HAHA That's what I was thinking!!

    HAHA That's what I was thinking!!
  11. Wait - you said you did a compression check -...

    Wait - you said you did a compression check - need to spin the motor over to do that so how does it not move now?
  12. Replies
    10
    Views
    400

    For me make sure the splines are engaged, and the...

    For me make sure the splines are engaged, and the through hull rides on the smooth surfaces, and go with it....

    I've dealt with all variants and never had an issue following these guidelines...
  13. Replies
    7
    Views
    1,038

    Looks like full rebuild. Probably crank too.... ...

    Looks like full rebuild. Probably crank too....

    Carbs need rebuild kits as well, usually... All fuel lines should be updated.
  14. Replies
    7
    Views
    1,038

    Full rebuild here: ...

    Full rebuild here: http://greenhulk.net/forums/showthread.php?t=193805
  15. Replies
    3
    Views
    257

    I would use the 94 650 CDI. slightly advanced...

    I would use the 94 650 CDI. slightly advanced timing over the 93 750. Keep all the parts as they will be good for spares. I have lots of extra stuff if you need any misc parts and hardware. PM me...
  16. Replies
    3
    Views
    321

    Yes, as K447 said, remove the auto cock.

    Yes, as K447 said, remove the auto cock.
  17. A bad stator or a low fuel/oil will limit it out...

    A bad stator or a low fuel/oil will limit it out of the water in the 4k range. Since it is out of the water, have you tried disconnecting the grey wire from the CDI to the board?
  18. Where in Ohio are you? PM me for info....

    Where in Ohio are you?
    PM me for info....
  19. All are the same through 2002. PN 5410652 It...

    All are the same through 2002. PN 5410652

    It appears in the parts diagram under water inlet. https://parts.polarisind.com/Browse/Browse.asp
  20. I can give you some reed options. PM me if you...

    I can give you some reed options. PM me if you are interested.
  21. https://www.ebay.com/itm/Polaris-Jet-Pump-Stator-O...

    https://www.ebay.com/itm/Polaris-Jet-Pump-Stator-O-Ring-5410652-SL-SLT-SLX-SLH-SLTH-SLTX-PRO-Virage/223669404853?_trkparms=aid%3D1110006%26algo%3DHOMESPLICE.SIM%26ao%3D1%26asc%3D225074%26meid%3D703bf0...
  22. Replies
    7
    Views
    597

    The SLT750 exhaust manifold has 9 bolts, all the...

    The SLT750 exhaust manifold has 9 bolts, all the same length, 3 per cylinder. There should be a gasket in between the cylinders and the manifold (it is usually one piece and pretty thick), and the...
  23. Replies
    19
    Views
    908

    PTO looks like it is showing lean burn - center...

    PTO looks like it is showing lean burn - center of the piston is becoming pitted or the spark plug is contacting the dome - what plugs are you running? And is there a .50 stamped on it?
  24. 18 should be fine

    18 should be fine
  25. If it didn't damage the other wires in the...

    If it didn't damage the other wires in the harness, there is an easier way.....
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4