Search

Type: Posts; User: TJS0712F

Page 1 of 8 1 2 3 4

Search: Search took 0.01 seconds.

  1. http://greenhulk.net/forums/showthread.php?t=24713...

    http://greenhulk.net/forums/showthread.php?t=247134
  2. Replies
    8
    Views
    776

    What does the engine oil look like. If it has...

    What does the engine oil look like. If it has pretty shimmering shiny specs of goldish color in the oil you have a thrust bearing issue, where the crankshaft walked forward cause the impeller wants...
  3. Yes tap it out with a brass drift from the other...

    Yes tap it out with a brass drift from the other side. See my post on Pump refurb. Mine was so hammered I had to just skim it with a boring bar on my milling machine before I rebuilt it.
  4. Replies
    93
    Views
    19,163

    I have two wedges in my 12F. Gained some MPH. I...

    I have two wedges in my 12F. Gained some MPH. I would not go back to stock.
  5. Replies
    8
    Views
    776

    http://greenhulk.net/forums/showthread.php?t=24713...

    http://greenhulk.net/forums/showthread.php?t=247134
  6. Yes I agree. That material has to be milled/cut...

    Yes I agree. That material has to be milled/cut out. New piece(s) made. Not a big deal if you have a mill and some material. Sounds like the person you brought it to does not know how to make parts...
  7. I could prob fix that. I know somewhere on here I...

    I could prob fix that. I know somewhere on here I have a post where I welded a GP1300 back together. It was like humpty dumpty.
  8. Post pics of said hole.

    Post pics of said hole.
  9. Replies
    6
    Views
    806

    Did you take the tail cone off and remove the...

    Did you take the tail cone off and remove the back bearing to get a look at the inside of the bearing housing, bearings and rear part of shaft. Water intrusion is common and will take out bearings in...
  10. Replies
    33
    Views
    2,332

    I have been preaching this for years. I take my...

    I have been preaching this for years. I take my pump apart twice a year. Never a problem now. I have a full rebuild post on here somewhere.
  11. Replies
    5
    Views
    355

    They make 4 degree wedges for these pumps. It...

    They make 4 degree wedges for these pumps. It creates some bow lift and has no ill effect on handling of the machine. I have a 12F similar hull and I run two wedges with no probs. It does leap out of...
  12. Replies
    8
    Views
    596

    WTB - Parts These used displays get a pretty penny. Remember...

    These used displays get a pretty penny. Remember folks. The hours are logged into the display. So if your machine has 40hrs on it and you buy a used display, you might get a display that reads a lot...
  13. Replies
    5
    Views
    532

    Here in the CT. there are only a few Upholstery...

    Here in the CT. there are only a few Upholstery shops around my area. I can imagine in FL there are many with a year round boating season. You probably have your choice of many. As others have stated...
  14. I know what he is getting at. To prevent from...

    I know what he is getting at. To prevent from cracking (from rapid heat input) elsewhere an overall heat of 200-250 degrees would be good. I have put many parts in a gas grille I modified for this...
  15. To the Op. Post your location. I know I can fix...

    To the Op. Post your location. I know I can fix that window. I welded a GP1200 block back together a few years ago. Still runs today.
    T.J.
  16. Replies
    17
    Views
    1,115

    Norton makes Bear-Tex. Not 3M.

    Norton makes Bear-Tex. Not 3M.
  17. Thread: Closed Thread

    by TJS0712F
    Replies
    3
    Views
    519

    Sorry just got back from Fla. I am in FFld. PM me...

    Sorry just got back from Fla. I am in FFld. PM me if you want.
  18. Replies
    6
    Views
    722

    Pull the pump and inspect the whole thing....

    Pull the pump and inspect the whole thing. Impeller, bearings (pop rear cone off). Impeller to wear ring clearance.
  19. Replies
    10
    Views
    565

    How many hours on this machine. Have you checked...

    How many hours on this machine. Have you checked the wear ring to impeller clearance. Have you looked at the impeller to see if it is damaged. I take my pump out and apart two times a year....
  20. Thread: Closed Thread

    by TJS0712F
    Replies
    3
    Views
    519

    I don't have the answer about the holes. Maybe...

    I don't have the answer about the holes. Maybe others will chime in. If you need those welded up send them to me across the pond to CT. I will TIG them up if you want. Pay shipping both ways and a...
  21. That is much wider than a Karavan double I had...

    That is much wider than a Karavan double I had just by looking at those pics.
  22. Replies
    21
    Views
    1,918

    Post your location.

    Post your location.
  23. Sticky: Folks. This is how it is done. Nice job. Keep...

    Folks. This is how it is done. Nice job. Keep checking your clearences when machining od grinding the impeller. Shoot for .008". Might have to sand down that hump where the ring is welded.
  24. Sticky: Did you press a wear ring in it ?

    Did you press a wear ring in it ?
  25. Replies
    2
    Views
    343

    Put down the drill and do the welder method as...

    Put down the drill and do the welder method as stated. I think I might have a post here somewhere where I show pics of a broken, seized fastener showing the welding method.
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4