Search

Type: Posts; User: sdlvx

Page 1 of 8 1 2 3 4

Search: Search took 0.04 seconds.

  1. If you are running quality oil you can run better...

    If you are running quality oil you can run better than 50:1. But because the carbs are providing the oil to lubricate your engine, if something goes wrong with your carbs you don't get enough oil....
  2. Replies
    12
    Views
    131

    In addition to everything K447 said, I had...

    In addition to everything K447 said, I had problems on one of my skis because I replaced a 2 PSI vent check valve with one with no pressure.

    When you start it, if there's no trapped air pressure...
  3. Sticky: Top deck looks pretty cool and unique.

    Top deck looks pretty cool and unique.
  4. Replies
    5
    Views
    160

    Are you around Chicago?

    Are you around Chicago?
  5. Thread: Fuel filter gunk

    by sdlvx
    Replies
    18
    Views
    918

    Funny you mention that. I have the same gunk in...

    Funny you mention that. I have the same gunk in one of my skis after I put premium in it. I'm in Wisconsin but it's still weird. Same can I've always been using and never had a problem with either....
  6. Replies
    4
    Views
    279

    I am probably going out on the last ride on the...

    I am probably going out on the last ride on the Pro today or tomorrow before I put it away for the season. Water is getting too cold for it, it's probably mid to lower 60s in the middle of the lake...
  7. Sticky: I believe I have downloaded the entire site that...

    I believe I have downloaded the entire site that is available, including available images and PDFs. At the very least I have a back up.
  8. Replies
    11
    Views
    487

    It can also do it if a carb is messed up to the...

    It can also do it if a carb is messed up to the point it barely lets in any fuel but isn't completely blocked.
  9. Try ebay, I see some solas ones on ebay.ca that...

    Try ebay, I see some solas ones on ebay.ca that have free shipping and are around CAD$25. I had a spare driveshaft that was destroyed and I just cut off the impeller end and welded a nut to it. If...
  10. Replies
    15
    Views
    1,675

    What hulls does this fit in?

    What hulls does this fit in?
  11. Early Polaris are pretty unique animals. Maybe if...

    Early Polaris are pretty unique animals. Maybe if you give us some pictures we can help. I've never dealt with one either. But if you were looking at a Sea Doo from that era, you would be looking at...
  12. Replies
    24
    Views
    928

    That is him in a nutshell, lol.

    That is him in a nutshell, lol.
  13. Replies
    24
    Views
    928

    http://greenhulk.net/forums/attachment.php?attachm...

    http://greenhulk.net/forums/attachment.php?attachmentid=478673&stc=1http://greenhulk.net/forums/attachment.php?attachmentid=478674&stc=1http://greenhulk.net/forums/attachment.php?attachmentid=478675&s...
  14. Replies
    24
    Views
    928

    I bought this as a rescue ski from some guy who...

    I bought this as a rescue ski from some guy who really didn't know what he was doing. I was told, by him, that he sent the crank to crankworks, they lost it, so they stroked a 750 crank for him for...
  15. Replies
    24
    Views
    928

    Is there a difference between Pro 785 cases...

    Is there a difference between Pro 785 cases between years? 98 and 97 have different part numbers than 99 and later. But I got bit by this before with my small end crank pushing.
  16. Replies
    24
    Views
    480

    Maybe you can get to some stuff with the carbs on...

    Maybe you can get to some stuff with the carbs on the ski, but it's a constant nightmare of dropping something in the hull. Even if you put rags down underneath where you are working. It's just flat...
  17. Replies
    7
    Views
    190

    3M 4000, or 5200. Higher number is how permanent...

    3M 4000, or 5200. Higher number is how permanent you want it to be. You can get 5200 off if you are dedicated but it's more for situations when you're applying things like the wear ring to the hull...
  18. Replies
    2
    Views
    203

    Are you talking like the WSM aftermarket ones...

    Are you talking like the WSM aftermarket ones that have a plastic ring instead of the stainless steel found in the OEM ones? I really doubt you'll find one new.
  19. Replies
    7
    Views
    190

    Run it on a trailer in the water with the seat...

    Run it on a trailer in the water with the seat off. I had a leak on my white pro 785 near the rubber coupler for the drive shaft through hull. Even though it's a hose with hose clamps it needs to be...
  20. Thread: BPR8ES or BR9ES

    by sdlvx
    Replies
    12
    Views
    3,277

    No, 7 is hotter, and once a plug gets too hot you...

    No, 7 is hotter, and once a plug gets too hot you can burn a hole in your pistons. 8s are just OK and somewhat safe, I wouldn't push it unless you feel like experimenting for us and maybe ending up...
  21. Replies
    10
    Views
    611

    I've had good luck with the stuff from Ace...

    I've had good luck with the stuff from Ace Hardware, in general. I bought plastic T fittings for the primer lines in one of my skis. The ones from Fleet Farm and the internet were all cheap plastic...
  22. Replies
    10
    Views
    611

    Do you remember where you bought it from?...

    Do you remember where you bought it from? Probably cheap chinese stuff that's probably not even real polyurethane.
  23. Replies
    24
    Views
    928

    Now that I think about it, it all makes sense....

    Now that I think about it, it all makes sense. The guy putting the new crank in, giving me an extra head while the last one as milled (probably to remove all the chunks of crap from FOD), mark on the...
  24. Replies
    19
    Views
    761

    Crankworks in AZ or Northern Crankshaft in MN,...

    Crankworks in AZ or Northern Crankshaft in MN, ship whatever is closest, or call around. You can find people who will do it local so you don't have to risk shipping it. Search for machine shops.
  25. Replies
    19
    Views
    761

    Wiseco/cometic for gaskets, WSM for pistons....

    Wiseco/cometic for gaskets, WSM for pistons. People hate on SBT, their reman engines seem to be the biggest problem with mechanics doing things wrong. Their parts seem alright, not OEM quality but if...
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4