Search

Type: Posts; User: LT1GMC

Page 1 of 8 1 2 3 4

Search: Search took 0.01 seconds.

  1. FS Price reduced to $120 shipped.

    Price reduced to $120 shipped.
  2. Replies
    0
    Views
    77

    FS - Parts GPR Coupling Insert

    GPR Coupling rubber insert, like new. $40 shipped US only
  3. Replies
    0
    Views
    57

    FS - Parts GPR/XLT Power Valve Motor and cable

    2001 GPR Power Valve Motor. Nice and works well, was removed to go to 1390 fixed valve build. $55 shipped US only.
  4. Replies
    0
    Views
    55

    FS - Parts GPR/XLT Electrical Box

    2002 GPR electrical box, complete and working except module "may" be bad. I had swapped with another XLt I was working on and later found the real cause was a plugged up carb. I honestly cannot...
  5. Just drill out but be sure not to use a drill...

    Just drill out but be sure not to use a drill larger than the original hole size. I bought factory rivets and painted the heads black after install on mine to match the trim. Probably could use any...
  6. Replies
    4
    Views
    217

    I had a similar problem on a 1200R that I had...

    I had a similar problem on a 1200R that I had just rebuilt, carbs and all. Did all the checks like you, took carbs back apart 2 times, reset pop off, finally found the issue: a piece of corrosion(...
  7. Replies
    16
    Views
    762

    I use the Stabil Blue Marine which is supposed to...

    I use the Stabil Blue Marine which is supposed to help reduce the negative effects of ethanol enhanced fuel. Have not had any issues in many years. Started using it to combat corrosion in 2 stroke...
  8. Replies
    5
    Views
    490

    We have/had 3 09 FZR/S in the family, all about...

    We have/had 3 09 FZR/S in the family, all about 82-83 mph. One has stock newer I/C and does just fine in Indiana weather. ET LB wheel in mine. Only traded up to GP1800 because of ride in the rough...
  9. Oil mist passing thru the supercharger means it...

    Oil mist passing thru the supercharger means it is also passing thru the innercooler. An oil coating on all the heat transfer surfaces reduces the efficiency of heat transfer. It also will eventually...
  10. Replies
    13
    Views
    837

    With the nose riding higher there will be a...

    With the nose riding higher there will be a greater opportunity for the pump to get air in it on less than smooth water, thus higher rpm and less efficiency during rougher water.
  11. Replies
    35
    Views
    2,070

    That is the nozzle I am using, just used a...

    That is the nozzle I am using, just used a flapper wheel to get it to 87mm. The inlet of all the SHO-SVHO pumps and nozzles is the same, its only the wear ring that is 160 mm.
  12. Replies
    8
    Views
    352

    The 4.9 in my son's supercharged boat will not...

    The 4.9 in my son's supercharged boat will not last, but the 4.2 in my 09 FZS has been on the original sensor for 6 years and 145 hours, still working fine(never been out). Both have Innovate...
  13. Replies
    8
    Views
    533

    I would take a look at the map sensor and be sure...

    I would take a look at the map sensor and be sure it is connected completely and also that the hose/fitting it is connected to is correct and in place. Perhaps it did not get put back in place good...
  14. A fouled plug or bad coil will act this exact way...

    A fouled plug or bad coil will act this exact way too, 1800's are so powerful you may not notice the miss but the rpm will show it. Its happened to me 2 times on my modded FZS.
  15. Replies
    35
    Views
    2,596

    I ordered mine online at diylettering and using...

    I ordered mine online at diylettering and using the measurements from the space on the GP managed to preview and change the font to get a set of letters that would fit perfectly. State law in Indiana...
  16. I have a Garmin E-Trex GPS which does a great...

    I have a Garmin E-Trex GPS which does a great job. It is water resistant (but does NOT float) records speed and also has a reset-able maximum speed. I usually keep it in the glove box for speed runs...
  17. Replies
    12
    Views
    640

    You may want to check clearance from the back of...

    You may want to check clearance from the back of the impeller blades and the front edge of the pump vanes.

    Guys used to cut the impeller hub to get it closer to the pump to improve performance....
  18. I believe you can just buy the maptuner without a...

    I believe you can just buy the maptuner without a tuning license. Then if you have a tune in it you are good to go.
  19. Thread: FZR seat

    by LT1GMC
    Replies
    8
    Views
    360

    WTB - Parts Wow, why would you want take an awesome, custom...

    Wow, why would you want take an awesome, custom covered 3 passenger seat and dumb it down to 2 passenger? Next are you gonna paint it blue? :)
  20. Replies
    28
    Views
    2,029

    Thought I might add that a wastegate is on a...

    Thought I might add that a wastegate is on a turbo and relieves exhaust pressure to keep the boost under control by slowing the turbo. Superchargers use a blow off valve (BOV) or a bypass valve which...
  21. Replies
    4
    Views
    303

    Get a bolt that just slides in the tube from the...

    Get a bolt that just slides in the tube from the inside, heat the outside nozzle area around the tube, and tap it out. Once the bolt head is about flush with the inside wall of the nozzle use a drift...
  22. Replies
    28
    Views
    2,029

    Please post both you guys results, inquiring...

    Please post both you guys results, inquiring minds wanna know.
  23. Replies
    128
    Views
    6,109

    2016 FZR's had them originally and are shown on...

    2016 FZR's had them originally and are shown on the parts listings. On the 09's and up a few years there was an issue with foam breaking and covering the vent intake completely. They revised the...
  24. Replies
    13
    Views
    1,047

    I believe the original worry about the stock 19...

    I believe the original worry about the stock 19 grate breakage potential was from a post stating they were going to grind, remove the middle bar, and thin out the other bars on a 19 grate. That...
  25. Replies
    9
    Views
    598

    I would consider another oil change shortly, if...

    I would consider another oil change shortly, if you take the clutch apart you will see the sprag and roller bearings have a lot of wear on them and that worn off metal may all be in the filter but...
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4