Search

Type: Posts; User: 2fast4u

Page 1 of 8 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    67
    Views
    2,314

    For the unknowing people MCCT= mechanical cam...

    For the unknowing people MCCT= mechanical cam chain tensioner ACCT= automatic cam chain tensioner
  2. Replies
    67
    Views
    2,314

    With a 09 fzr and i want to just up grade the...

    With a 09 fzr and i want to just up grade the chain and guides to the larger one, what part numbers do you use for the cam chain gears? (my understanding is then bolt pattern on the cam gears changed...
  3. What about Honda PWC they were turbo?

    What about Honda PWC they were turbo?
  4. IF you think you have a injector problem pull...

    IF you think you have a injector problem pull them out and have a injector cleaning service check them for flow, leaking, and correct operation. This is the only way to be sure they are operating...
  5. Replies
    22
    Views
    758

    the most you want to re pitch any propeller is...

    the most you want to re pitch any propeller is two pitches max, any more than that the propeller blades tend to crack plus the blade casting does not match the wear ring dia very well. I know from...
  6. Replies
    12
    Views
    692

    do not be too quick to add washers to the back of...

    do not be too quick to add washers to the back of the plate. If you are truly hitting the rev limiter ever so slightly the loss in power will cause the ski to bounce some because there is not enough...
  7. Replies
    12
    Views
    692

    no need to remove the exit pipe where it goes out...

    no need to remove the exit pipe where it goes out the hull, just remove the ride plate and use a sharp blade to trim the flap fingers off. Also if your vxr has the rubber curtain around pump leave it...
  8. Replies
    12
    Views
    692

    on the exhaust mod did you trim about 3 inches...

    on the exhaust mod did you trim about 3 inches off the exhaust hose end that extends down inside the plastic box and remove the rubber flap fingers where the exhaust exits the hull. also you need to...
  9. Replies
    2
    Views
    148

    clogged or kinked vent hose or possible bad one...

    clogged or kinked vent hose or possible bad one way vent hose valve check the entire vent system hose. There is a problem for sure in the hose vent system.
  10. did you crack the hull from towing something...

    did you crack the hull from towing something using the two tie down hooks ? HOW DID THIS DAMAGE HAPPEN?
  11. Replies
    12
    Views
    650

    good news it the inner liner is NOT around the...

    good news it the inner liner is NOT around the pump tunnel crack area.
  12. Replies
    2
    Views
    163

    inspect intake grate for an obstruction , then...

    inspect intake grate for an obstruction , then replace all sparkplugs and re test.
  13. Replies
    12
    Views
    650

    the aftermarket intake grate makes more tunnel...

    the aftermarket intake grate makes more tunnel pressure as it feeds more water to the pump, most of the time it is not a problem till you mod your ski and start pushing speeds close to 80+ however...
  14. Replies
    22
    Views
    758

    good luck you are on the right track for sure ,...

    good luck you are on the right track for sure , keep us posted TommyJordan
  15. Replies
    12
    Views
    650

    This problem has been around for over 10 years...

    This problem has been around for over 10 years here is a link http://greenhulk.net/forums/showthread.php?t=49610 here is a second link, Do your home work before you build a 80 to 90+ mph ski. Tommy...
  16. Thread: What speed?

    by 2fast4u
    Replies
    3
    Views
    236

    78 to 80 mph with a cut ride plate and a prop...

    78 to 80 mph with a cut ride plate and a prop pitch that will allow you to get close to 8400+ rpms
  17. Replies
    15
    Views
    736

    R&D plates are much faster than a Riva plate on a...

    R&D plates are much faster than a Riva plate on a gpr. Put a post on the forum looking for a used one.
  18. Replies
    15
    Views
    736

    the missing main part is a correct ride plate...

    the missing main part is a correct ride plate angle when done correctly it is worth 4 mph
  19. Replies
    74
    Views
    16,792

    You might want to drive and enjoy the trip over,...

    You might want to drive and enjoy the trip over, less chance of covid I am sure.
  20. Old post I did 10 years ago for the new guys! Prop pitch and rpm's

    Here is a old post i started 10 years ago (where have the years gone) about prop pitch and rpm's here is the link http://greenhulk.net/forums/showthread.php?t=135520 Tommy Jordan
  21. Sticky: I wanted to bring this topic back up for all the...

    I wanted to bring this topic back up for all the new guys.
  22. Replies
    22
    Views
    758

    100% correct information here! also here is a...

    100% correct information here! also here is a good post I did 10 years ago. Man where have the years gone! http://greenhulk.net/forums/showthread.php?t=135520
  23. Replies
    7
    Views
    379

    I did not need one on my ski, 09 fzr, i just used...

    I did not need one on my ski, 09 fzr, i just used the oem spacer , my prop does sit close to stator but the closer the prop is to the stator the better the pump pressure. Riva even offered a set back...
  24. Replies
    22
    Views
    758

    Reducing the prop pitch INCREASES acceleration...

    Reducing the prop pitch INCREASES acceleration and top engine rpms, this is a must do for higher elevations.
  25. Replies
    7
    Views
    379

    get a old damaged wear ring for your ski and send...

    get a old damaged wear ring for your ski and send it to scat trac and have them install a 160 stainless wear ring then purchase a 160 prop your desired pitch and you are good to go (the water engine...
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4