Search

Type: Posts; User: Myself

Page 1 of 8 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    7
    Views
    109

    Set it on the AC scale at 200, yes on black and...

    Set it on the AC scale at 200, yes on black and purple (excitor coil). Crank it, looking to see how many volts it cranks out.
  2. Replies
    7
    Views
    109

    I think it will crank with just battery hooked up.

    I think it will crank with just battery hooked up.
  3. Replies
    1
    Views
    66

    Did you try running it with stop switch...

    Did you try running it with stop switch disconnected?
  4. Replies
    7
    Views
    109

    Most likely bad stator. What is the ac voltage...

    Most likely bad stator. What is the ac voltage output of that excitor coil while cranking?
  5. Replies
    1
    Views
    55

    Board is labeled by color, put the colored wires...

    Board is labeled by color, put the colored wires where they go.
  6. Replies
    4
    Views
    95

    It can be difficult to see fuel flowing.

    It can be difficult to see fuel flowing.
  7. Replies
    4
    Views
    95

    Check every cylinder individually after the...

    Check every cylinder individually after the engine is a bit warm. It should start on each cylinder individually on the trailer. If the one doesn't, then try swapping plugs or squirting a wee bit of...
  8. Replies
    6
    Views
    188

    That's not a great pic but you're looking for a...

    That's not a great pic but you're looking for a stamped "o" near the crank journals. And also on the rods near the caps. Then use the chart posted above. If the crank has a stamped "o" but the rod...
  9. The shield on my wife's Fxho is smoked and looked...

    The shield on my wife's Fxho is smoked and looked like what you describe. The cracks are inside the plastic, caused by the sun. I used a red scotchbrite to fully remove oxidation then buffed it out....
  10. Replies
    1
    Views
    63

    You'll need to open the electrical box and test...

    You'll need to open the electrical box and test for output voltage of the solenoid.
  11. Replies
    4
    Views
    115

    Crack both high speed sdjusters open to 1/2 turn....

    Crack both high speed sdjusters open to 1/2 turn. If the prblem goes away then you know it's related to fuel delivery or the engine sucking a bit of air through a bad seal or gasket.
  12. Thread: weird noise

    by Myself
    Replies
    5
    Views
    171

    Whining, whirring sound is almost always jet pump...

    Whining, whirring sound is almost always jet pump bearings. Pull it for inspection.
  13. Thread: weird noise

    by Myself
    Replies
    5
    Views
    171

    Can't tell anything from that vid. What kind of...

    Can't tell anything from that vid. What kind of noise?
  14. Replies
    5
    Views
    154

    I have also had to put a new iac on an stx15 for...

    I have also had to put a new iac on an stx15 for thse same symptoms.
  15. If everything else looked good then I'm guessing...

    If everything else looked good then I'm guessing a ring is stuck in the grooves.
  16. Replies
    5
    Views
    204

    After oil is pretty clean, just take it out and...

    After oil is pretty clean, just take it out and ride it for a good half hour. That's all I've ever done. You can run it at various throttles strapped to the trailer if you want to as well.
  17. Yes, there is always a bit of power to gain with...

    Yes, there is always a bit of power to gain with port cleanup. You will never notice a difference until you do a lot more modding.
  18. Did you pull the rings off the piston and clean...

    Did you pull the rings off the piston and clean them while it was apart?
  19. I agree, those are non maintenance items, replace...

    I agree, those are non maintenance items, replace when they quit.
  20. Replies
    6
    Views
    188

    Did you try new spark plugs?

    Did you try new spark plugs?
  21. Replies
    2
    Views
    147

    Just get a good used hose from Westside...

    Just get a good used hose from Westside Powersports. Those guys have all the used Seadoo parts.
  22. Replies
    4
    Views
    127

    There should be a grease zirk on it. Standard...

    There should be a grease zirk on it. Standard grease gun, a couple pumps.
  23. Replies
    4
    Views
    127

    You can usually "unseat" tge bellows without much...

    You can usually "unseat" tge bellows without much force. You can loosen the rearmost hose clamp and shove it forward some. Then when everything is back together, pump a bit of grease into the pto,...
  24. Replies
    8
    Views
    271

    Pull the front cover and clean all the metal...

    Pull the front cover and clean all the metal shavings out of the magneto.
  25. Replies
    14
    Views
    440

    The one that I fixed that was doing this had a...

    The one that I fixed that was doing this had a cracked piston.
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4