Search

Type: Posts; User: Saum700p

Page 1 of 8 1 2 3 4

Search: Search took 0.83 seconds.

  1. Replies
    166
    Views
    25,477

    You can start by pulling that 11/15 out of...

    You can start by pulling that 11/15 out of there.. I tried it it's trash. You are better off with a stock impeller pitched then that all day.
  2. Replies
    6
    Views
    172

    Im running the ones from the older worx fx/fz on...

    Im running the ones from the older worx fx/fz on my gp and vxr. The mounting holes are the same. Not sure if the riva are better, but the worx are more than enough for me and i'm running them in...
  3. Problem is the damage to the hub from the old...

    Problem is the damage to the hub from the old clutches.
  4. Replies
    6
    Views
    217

    Time the cams with the dots on the cam and the...

    Time the cams with the dots on the cam and the middle cap arrows. They should look identical to the the other ones by eye. You're good.
  5. Replies
    7
    Views
    325

    I have one in New Orleans, 23 hours pulled from...

    I have one in New Orleans, 23 hours pulled from 2018.
  6. Replies
    6
    Views
    217

    Tape should be fine. I put some red loctite on...

    Tape should be fine. I put some red loctite on mine.
  7. Replies
    6
    Views
    217

    Cam Gear Tq. 24nm or 17.7 ftlb. Cam Caps...

    Cam Gear Tq. 24nm or 17.7 ftlb. Cam Caps 16nm or 11.8 ftlb. Red lock tight on the cam gear oil on the cam caps. Set all the cam caps hand tight and walk them down. Manual doesn't list an...
  8. Replies
    31
    Views
    1,947

    ouch...

    ouch...
  9. Replies
    2
    Views
    375

    I believe they were smaller then that, off the...

    I believe they were smaller then that, off the interior pump lines were less then 10 if I remember right
  10. I don't have a picture of it but I used a squall...

    I don't have a picture of it but I used a squall and grinder to notch out my plugs till the plate gasket seated up tight then put l little 5200 on it when it was finished to hold it in place.
  11. The quality definitely isn't there with he pump...

    The quality definitely isn't there with he pump seal. I don't know why they can't just fill the voids on the grate with the stuff and leave it in there sell it as a package.
  12. Ill second the clutch... 50 mph 6,000 rpm is...

    Ill second the clutch... 50 mph 6,000 rpm is what I had when mine went out. Just pull the tube on the front of the supercharger and spin the impeller with your finer. Spins both ways? You need a...
  13. Replies
    2
    Views
    145

    I have worx on mine they bite plenty hard. I even...

    I have worx on mine they bite plenty hard. I even have them in the up position. I got a good bit of side bite with my Dean's cut ride plate. Might want to look into that kills two birds with one...
  14. Replies
    3
    Views
    315

    Possibly running too cold. What are the temps at...

    Possibly running too cold. What are the temps at your location. I took mine out in the late winter months and had some condensation in the oil cap. After it warmed up they are gone.
  15. Replies
    32
    Views
    2,466

    Copy his are having leaking issues? Asking for a...

    Copy his are having leaking issues? Asking for a buddy. I went tail, and i'm having no issues but his ski is dumping boost at the top end for some reason. either this or clutch going out but after...
  16. Replies
    5
    Views
    265

    Air filter, tune, and impeller is a great start. ...

    Air filter, tune, and impeller is a great start. Consider Dean's tunes they are excellent, and he does a tune and impeller combo.
  17. Thread: Vxr cams

    by Saum700p
    Replies
    11
    Views
    566

    I saw several mph out of the cams and...

    I saw several mph out of the cams and reflash/repitch on mine. doing cams also puts you at the max of the fuel system so you're going to need to do a pump and regulator. Get with your tuner to set...
  18. Replies
    22
    Views
    1,453

    Dean makes a plate which i've seen at 82+ no...

    Dean makes a plate which i've seen at 82+ no porpoising. Might want to try giving him call.
  19. Those mods are great, I have done them on both of...

    Those mods are great, I have done them on both of my skis. But you are not going to unlock any power until you tune the ski. It will be factory speed limited. I suggest the air intake and filter,...
  20. Replies
    22
    Views
    1,453

    Trim extender is not going to fix that. There...

    Trim extender is not going to fix that. There have been a few people complaining about the Riva plate porpoising unfortunately.
  21. Thread: Trim Wedge

    by Saum700p
    Replies
    4
    Views
    264

    Yes unfortunately. The wedge is machined and...

    Yes unfortunately. The wedge is machined and fits up tight to the stator. When tightening the 4 pump bolts just look inside the pump to make sure the vanes are aligned.
  22. Replies
    18
    Views
    1,212

    I lost my clutch on the GP at 103 hours. Ran...

    I lost my clutch on the GP at 103 hours. Ran amsoil since 23 hour service. No clue if it was something that would have extended by different oil. Have to look at it when it comes out this week, but...
  23. So Which nozzle exactly did you run equating to...

    So Which nozzle exactly did you run equating to which speeds? I thought about throwing my 83mm on my vxr one day to see what it did but it's an 8 vane. coming off the 6 vane stator and hitting those...
  24. Replies
    20
    Views
    1,245

    I've already spoken with him on my situation, our...

    I've already spoken with him on my situation, our group is in regular contact with Dean. For me, we decided it was probably best to go back with a stock one and see. Based on this clutch we'll...
  25. Replies
    20
    Views
    1,245

    Be careful dropping that fuel pressure to 20psi....

    Be careful dropping that fuel pressure to 20psi. you'll burn a piston quick. To run that big of a pump, you need to have a matching fuel map. I'm working with Dean's to get mine correct, but if you...
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4