Search

Type: Posts; User: JeffSki

Page 1 of 8 1 2 3 4

Search: Search took 0.31 seconds.

  1. Replies
    0
    Views
    79

    WTB - Parts 2017 300 Fuel Injector

    Looking for 1 known working fuel injector for a 300 (green). Part number 420874000.
  2. Replies
    7
    Views
    450

    I've used a few of the early aftermarket units,...

    I've used a few of the early aftermarket units, rather unimpressed with them. Had to grind down a corner to fit, also had to make a paper gasket cause the rubber would squish out with any torque. ...
  3. Replies
    7
    Views
    450

    View Post

    I don’t see a number
  4. Replies
    7
    Views
    450

    Throttle Body Bearings?

    Has anybody sourced out replacement throttle body bearings?

    http://greenhulk.net/forums/attachment.php?attachmentid=458759&stc=1
  5. Replies
    1
    Views
    156

    WTB IBR Module Assembly

    Need a known working clean used IBR assembly for my 12 PX, shipped to 33410. Thx
  6. Def not gonna spend $2k for a new crank, the ski...

    Def not gonna spend $2k for a new crank, the ski is prob only worth $3k.

    The only ss sleeves I can find are only 8mm wide, which would mean i'd have to use 3 of them for the 3 seals. Would also...
  7. Thanks for the reply. What do you mean "BPR fix",...

    Thanks for the reply. What do you mean "BPR fix", buy a new crank?

    Thinking I can just turn down the rusty end of the crank and buy seals with a smaller ID.
  8. Sleeve Avalable For Output Side of the Crankshaft?

    Is there a ss sleeve avail to cover the rusted area of the crank where the seals ride? Or another way to correct this issue (without buying new crank)?
  9. Replies
    0
    Views
    146

    WTB - Parts 2005 FX HO Wire Harness Assembly

    Looking for a good main harness to fit a 05 FXHO. The part number is 6B6-8259L-10-00. From fresh water ski please.
  10. Replies
    6
    Views
    1,273

    WTB - Parts still have?

    still have?
  11. Replies
    1
    Views
    553

    Replacing Spark IBR Help

    To replace a ibr actuator on a HO spark, does the new one need to be “married” or calibrated by a dealer after installed?
  12. Thread: Riva Exhaust

    by JeffSki
    Replies
    1
    Views
    303

    WTB Just the tip....

    Just the tip....
  13. Replies
    36
    Views
    4,402

    PM sent

    PM sent
  14. 2016 Stripped Driveshaft and Output Sleeve

    Have a 2016 3up 90hp with 50 hrs, bad splines on the shaft and output sleeve. It’s past 1 yr warranty, so how is this repaired? Doesn’t show the sleeve is a replaceable part, so new crank? Crazy! ...
  15. Replies
    8
    Views
    798

    WTB I do, where are you located? :p

    I do, where are you located? :p
  16. Replies
    8
    Views
    798

    WTB S. Fl, 33410

    S. Fl, 33410
  17. Replies
    8
    Views
    798

    WTB Actually it's a 2004, and has only 81 hrs. Does...

    Actually it's a 2004, and has only 81 hrs. Does have some corrosion, compression is good. I have video of it running smoothly. $600 for the block/head/head cover.


    ...
  18. Replies
    8
    Views
    798

    WTB Are you interested in a 03 GTX SC engine?

    Are you interested in a 03 GTX SC engine?
  19. Replies
    9
    Views
    1,421

    We rode from Blind Pass up to north tip of...

    We rode from Blind Pass up to north tip of Gasparilla, mostly on the gulf. Very nice ride, esp Cayo costa.
  20. Replies
    9
    Views
    1,421

    Sounds good! Are there many slow zones when...

    Sounds good! Are there many slow zones when going back on the intercoastal side?
  21. Replies
    9
    Views
    1,421

    Sanibel Captiva Area

    Gonna be there for a few days with my waverunner. Are there any “must see” destinations around there? Cool islands? Beaches?
  22. Replies
    10
    Views
    769

    FS Yes it does, but the handling fees would kill you

    Yes it does, but the handling fees would kill you
  23. Replies
    10
    Views
    769

    FS I’m not positive, but pretty sure it’s earlier...

    I’m not positive, but pretty sure it’s earlier than that.
  24. Replies
    10
    Views
    769

    FS FREE 2005 RXP Hull

    This is a 100% stripped hull, that’s been sitting for many years. The gel coat on the top deck is in excellent shape (just very dirty). The bott is good but does have gel coat stress cracks each side...
  25. Replies
    1
    Views
    543

    WTB - Parts Need Low Hour 1.8 NA Block

    Looking to buy a good, running 1.8 non-sc engine block assembly.
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4