Search

Type: Posts; User: butterbean_29512

Page 1 of 8 1 2 3 4

Search: Search took 0.38 seconds.

  1. Replies
    4
    Views
    104

    Putting it back on oil injection is a very smart...

    Putting it back on oil injection is a very smart move. Just make sure you use quality tygon line, and use oetiker clamps to clamp the ends. 1/8x1/4 line is what you need. I can get you a part...
  2. Replies
    17
    Views
    398

    Posted on your other thread about your high side...

    Posted on your other thread about your high side screws. I think your carb bodies are mashed in by hitting the OEM screws by mistake while drilling them out. Would cause all your problems you are...
  3. I hate to be the bearer of bad news but you...

    I hate to be the bearer of bad news but you probably pushed the original ones in when you drilled them out. It happens. If you have done that, the bodies are junk. I would check and verify with...
  4. Replies
    23
    Views
    7,324

    Rest assured, the 4200 is more than adequate to...

    Rest assured, the 4200 is more than adequate to seal the shoe. 5200 is way too aggressive. These are parts that you will probably have to remove at some later point. I would also suggest checking...
  5. If there are no mods on your ski, the factory...

    If there are no mods on your ski, the factory settings are usually the optimum settings. Especially pop off. I'd look up the factory settings and plug those in and try it.
  6. I didn't know the Concord would screw on to the...

    I didn't know the Concord would screw on to the HO pump threads. Never tried it. You learn something every day! If you try to use it you will have severe cavitation and erosion of the impeller...
  7. Replies
    2
    Views
    97

    I know exactly what you're talking about. It...

    I know exactly what you're talking about. It appears to be bubbling paint. Seems all Yamahas do it. My 2016 FX does it, and never sat in the sun a single day.
  8. You have to use genuine kits. Accept no...

    You have to use genuine kits. Accept no substitutes. Your runaway sounds like an air leak. You may have something going g on with your top end rebuild.
  9. Once you have gone supercharged, you will be...

    Once you have gone supercharged, you will be wasting your money getting a HO! I ride a '16 FXCSVHO and love it. I would never ever buy a HO platform.
  10. Looks to be an aftermarket Riva stinger pipe. I...

    Looks to be an aftermarket Riva stinger pipe. I guarantee you Riva will not have any info on it anymore.
  11. Replies
    1
    Views
    153

    If you rebuild it, it needs a careful inspection...

    If you rebuild it, it needs a careful inspection BEFORE you spend any cash on it. Since it ran dry of oil, you could have damaged all three cylinders and the crankshaft. If you have to replate the...
  12. FS TTT

    TTT
  13. Replies
    92
    Views
    1,973

    Sticky: For everyone that says we need to keep the...

    For everyone that says we need to keep the economy shuttered, I challenge them to give us a sustainable, workable way to keep the economy shuttered. We cannot continue this. They always have said...
  14. .004

    .004
  15. FS Yamaha 2016 FXCSVHO seat cover for sale

    Like the title says....2016 FXCSVHO OEM seat cover for sale. Removed it to install a JetTrim cover. Not faded, not ripped, never been pissed on! Great condition! (Both covers are included). Does...
  16. Replies
    13
    Views
    674

    no synthetic oil on the supercharged Yamaha...

    no synthetic oil on the supercharged Yamaha engine, the use of any oil with friction modifiers makes the clutch go out very quickly.
  17. Replies
    11
    Views
    669

    I guess it really depends on if you can afford to...

    I guess it really depends on if you can afford to replace the engine due to water ingestion. Cost of new IC or cost of new motor. Pretty clear cut decision to me.
  18. You haven't drilled out the holes yet?

    You haven't drilled out the holes yet?
  19. Replies
    30
    Views
    2,756

    You cannot just buy a prop and expect it to...

    You cannot just buy a prop and expect it to perform. You tune you prop last to achieve your target RPM's. I wouldn't waste my money on just a Riva stage 1 tune...IMHO they way overstate their...
  20. Open your fuel cap and see if the tank is in a...

    Open your fuel cap and see if the tank is in a deep vacuum right after it shuts off. If it is...you have a bad rollover check valve. Fairly common problem.
  21. I don't see how it is easy to do unless you have...

    I don't see how it is easy to do unless you have replaced the fuel lines. The supply line is much longer than the return line, and has a definite molded in curve in it. Hard mistake to make IMHO. ...
  22. Technically you both are wrong. The BOV simply...

    Technically you both are wrong. The BOV simply allows the SC to keep compressing air...which ensures airflow is in only one direction through the SC. Once again....SURGE IS VERY VERY BAD!!! Surge...
  23. The intake vacuum actuates the BOV. Vacuum...

    The intake vacuum actuates the BOV. Vacuum changes with load and throttle position.
  24. Every centrifugal compressor/supercharger needs...

    Every centrifugal compressor/supercharger needs one. It will save your clutch, or extend its life.
  25. The BOV keeps the compressor from operating in...

    The BOV keeps the compressor from operating in the surge index. Each centrifugal compressor...no matter it's intended use can aerodynamically compress only so much air. Once the compressor reaches...
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4