Search

Type: Posts; User: Weber Guy

Page 1 of 7 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    2
    Views
    273

    Sold !!

    Sold !!
  2. Replies
    2
    Views
    273

    New MSX-140 TPS

    I have (1) new MSX-140 TPS for sale.
    Polaris part #2202740.

    The price is $150.00 and shipping is included.
    The first person to send a message to weberpwr@outlook.com gets it.. My PayPal address...
  3. Coupler Removal Tool

    http://www.weberpower.com/tools-weber-drive-coupler-removal-tool.html
  4. I have a few new Pro-1200 driveshaft seal assy's...

    I have a few new Pro-1200 driveshaft seal assy's in stock.
  5. Replies
    9
    Views
    513

    That is the connector (header) I removed from a...

    That is the connector (header) I removed from a damaged Walbro ECU.
    I am working on a kit to replace the Bosch ECU with the newer Walbro components. It wouldn't be a cheap conversion, but at least...
  6. Replies
    9
    Views
    513

    How to remove potting epoxy

    I have a question for the ECU guru's.

    How can I dissolve the potting epoxy without damaging the pins or connector?
    I need this connector for a project.

    A PM is fine, or you can email me...
  7. It says you must have a current license; what...

    It says you must have a current license; what does this mean for the average MSX-150 / Bosch owner?
    Can anybody purchase this equipment, and use it for diagnostics? What steps would they have to...
  8. Replies
    16
    Views
    1,841

    Tools

    I would be interested if the price is reasonable; but I would like to see other members purchase anything they need, and we could discuss a package deal on the remaining items.
  9. Replies
    111
    Views
    5,848

    Trade Secrets

    http://www.greenhulk.net/forums/attachment.php?attachmentid=398250&stc=1[/QUOTE]

    It's hard to tell from the images, so I attached some top -secret info for you. Your MSX-150 most likely wont have...
  10. Replies
    111
    Views
    5,848

    The Camshaft lobes will NOT be parallel with the...

    The Camshaft lobes will NOT be parallel with the crankshaft at TDC.
    Throw away the OEM Polaris MSX repair manual, and use the Polaris FST manual instead.

    I saw an image earlier where you almost...
  11. Replies
    318
    Views
    13,677

    It's not easy to remove the rear bearing; I had...

    It's not easy to remove the rear bearing; I had to make my own puller.. The puller kit above is a good start, but it will still require some fabrication.
    The best option is to send it to Millennium,...
  12. Replies
    5
    Views
    1,616

    Weber Turbocharged Engine for Sale

    For Sale;
    A rebuilt Weber / Hydrospace watercraft Turbocharged short block. This has been rebuilt by a certified Weber engine rebuild center, and is a direct replacement for the Hydrospace...
  13. Replies
    31
    Views
    4,047

    Try This

    Try moving the fuel line restrictor to the other end of the "Y".
    Often the Novi separators stop working correctly. Start with a #60, and then experiment between a 60 -90 if this solution helps....
  14. You cannot compress the rubber, as the crankshaft...

    You cannot compress the rubber, as the crankshaft actually "floats" in the bearings. Most two strokes have a labyrinth locating pin, and snap rings on either side of the bearings to keep the...
  15. Alignment procedure

    368073

    Correct alignment is extremely critical in the Weber engine, as it doesn't have crankshaft bearings to absorb /support side load, etc, like the two-stroke Polaris models.

    When a Weber...
  16. Replies
    161
    Views
    9,112

    Another one

    I would like one also; Please contact me when possible.
    If possible, I will purchase them in larger quantity's and pass the savings on to GH customers.


    Thank you,
    Randy
  17. Replies
    20
    Views
    1,939

    Twin cylinder Ignition Timing, red domestic engines

    Virtually all the domestic twins except the hurricane share the same timing curve.
    It starts at 18, advances to 20, and then retards back to 18 at approx. 5000 Rpm.
    Just use a dial indicator,...
  18. Hey Cuda, I think he will travel to somebody...

    Hey Cuda,

    I think he will travel to somebody that can connect the software to his buggy.
    You must have been reading my mind, as if he couldn't find anybody to assist; I was going to ask you to...
  19. MSX-150 Diagnostic Sofware / Diagnosis Assistance Request

    Hi Everybody,

    I have a customer in Arizona that needs assistance.
    He has a UTV (very similar to a Polaris RZR), and he needs to find somebody with the Bosch MXS-150 diagnostic software and /or...
  20. NUJet Impeller for MSX-110 / 150 For Sale

    I have a new Polaris 5132372 NuJet 4.7 Impeller for sale.
    It's one of my favorite impellers for good Mph & decent hook-up.

    This can be used for a MSX110/150.
    Retail $293.00. I will sell it for...
  21. Replies
    48
    Views
    2,463

    If you lengthen the steering arm at the...

    If you lengthen the steering arm at the handlebars, you don't have to move the handlebars as far to make the turn nozzle travel thru it's full arc. *You will have to shorten the steering stops when...
  22. Replies
    48
    Views
    2,463

    If you lengthen the steering arm at the...

    If you lengthen the steering arm at the handlebars, you don't have to move the handlebars as far to make the turn nozzle travel thru it's full arc. *You will have to shorten the steering stops when...
  23. Replies
    48
    Views
    2,463

    The problem isn't necessarily the steering nozzle...

    The problem isn't necessarily the steering nozzle diameter; I would be cautious reducing the I.D. of it without careful testing & evaluation

    The correct way to increase the steering response;...
  24. Replies
    11
    Views
    1,209

    Gunmetal grey color is the kiss of death.. That...

    Gunmetal grey color is the kiss of death..
    That means you are on borrowed time.. You can burn down another piston in less than 4-5 minutes if the engine is too lean, too much timing, water temp too...
  25. Replies
    48
    Views
    2,463

    K-447 is 100% correct.. If you reduce and /or...

    K-447 is 100% correct..
    If you reduce and /or lengthen your steering nozzle too much, it has the same effect as installing a taller pitch impeller, and you can pull the engine off the torque curve...
Results 1 to 25 of 151
Page 1 of 7 1 2 3 4