Search

Type: Posts; User: Rxtxruss

Page 1 of 7 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    1
    Views
    208

    You will definitely be at 80mph (gps speed) the...

    You will definitely be at 80mph (gps speed) the dash will read slightly higher
  2. Replies
    12
    Views
    587

    You're very welcome, actually i was just thinking...

    You're very welcome, actually i was just thinking since your ski is a 2010 and the voltage regulator is in the back next to the battery you might be able to plug the 2020 stator directly into the...
  3. Replies
    12
    Views
    587

    What i ended up doing was cutting the new style...

    What i ended up doing was cutting the new style connector off of the 2020 stator and bought a new older style connector and pins and crimped them on the wires and then it plugged right into the...
  4. Replies
    12
    Views
    587

    This past summer i installed a brand new 2020 300...

    This past summer i installed a brand new 2020 300 engine into a 2016 rxp, the new engine was complete with pto cover and stator, the connector was different but it had the connector that plugs...
  5. You're welcome, happy to help, you could...

    You're welcome, happy to help, you could definitely just grab some stainless bolts from the hardware store and save some money!
  6. The part number for the hold down screw for the...

    The part number for the hold down screw for the coil is 420441383
  7. Replies
    20
    Views
    1,414

    The resistor plug would fit in the engine just...

    The resistor plug would fit in the engine just fine but since its a resistor plug it would just cut down on the amount of spark energy, I use the B08ZS and really like them
  8. Replies
    20
    Views
    1,414

    The R in the part number on Brisks website stands...

    The R in the part number on Brisks website stands for resistor, i was told that Riva had Brisk design the B08ZS for them and that is why Brisk does not list the non resistor version on their site
  9. Replies
    20
    Views
    1,414

    B08ZS is the correct plug, the picture is just...

    B08ZS is the correct plug, the picture is just generic

    I dont know why riva only lists these for the 300's, the terminal ends unscrew just like the plugs for the 215 and 260, i have had them in my...
  10. A 3 inch section works well

    A 3 inch section works well
  11. Replies
    1
    Views
    403

    2020 300 Engine Camshaft

    I am curious if anyone has any specs on the camshaft that is used in the 300 engine from 2018 and up, I'm in the middle of and engine replacement and noticed that the cam that's installed in the 2020...
  12. Replies
    2
    Views
    376

    Did you have a dealer recalibrate the system or...

    Did you have a dealer recalibrate the system or how was it accomplished? Sounds like maybe there is an intermittent issue with the throttle body possibly, there isn't that much information on that...
  13. Replies
    0
    Views
    167

    2012 RXPX IBR Issue

    I definitely have a strange problem here, 2012 rxpx 96 hours, freshwater ski its entire life, the ibr works great if i keep the ski under 60mph, in eco mode i can ride it all day long with the...
  14. Replies
    3
    Views
    574

    I wish there was room in the 16 and 17 hull to...

    I wish there was room in the 16 and 17 hull to upgrade to the 18 larger oil cooler! I hate the excess of cooling hoses everywhere and the potential for failure from added parts
  15. Everyone removing their supercharger should own...

    Everyone removing their supercharger should own an E8 wrench, for $15 its not worth dealing with a stripped bolt https://www.jbtools.com/vim-tools-wt0810-torx-box-wrench/
  16. Replies
    21
    Views
    1,019

    The carbon seal should be fine, but as tiderider...

    The carbon seal should be fine, but as tiderider said when the driveshaft gets pushed into the engine like it did it creates a ton of stress on the engines thrust bearings, just keep an eye on things...
  17. Replies
    21
    Views
    1,019

    The impeller coming unthreaded from the jetpump...

    The impeller coming unthreaded from the jetpump would definitely allow the hull to fill with water, it pushes the driveshaft forward and creates a gap in the hat and carbon seal letting the water in,...
  18. Replies
    9
    Views
    896

    To replace the pump seal you do have to remove...

    To replace the pump seal you do have to remove the jet pump assembly, might as well do the wear ring while you have the pump out, if your impeller has any damage at all you should replace it also or...
  19. Replies
    9
    Views
    896

    It most likely needs a new wear ring, look at the...

    It most likely needs a new wear ring, look at the wear ring through the intake grate from underneath and see if you can see any heavy gouges in it
  20. Replies
    5
    Views
    565

    You're welcome, I have swapped ECU's from a 14...

    You're welcome, I have swapped ECU's from a 14 rxtx to a 2009 rxt in the past for testing purposes and you are right about the buttons and trying to get into sport mode, its just different between...
  21. Replies
    5
    Views
    565

    Did you happen to reset the throttle body after...

    Did you happen to reset the throttle body after swapping ECU's? That could definitely be a reason its sluggish, probably not opening to 100%
  22. Replies
    12
    Views
    1,252

    You're very welcome, those bolt extractors really...

    You're very welcome, those bolt extractors really come in handy in a tight situation like that, i would definitely replace the allen head bolts with stainless hex head bolts, the updated bolts that...
  23. Replies
    12
    Views
    1,252

    There are special sockets that will bite into the...

    There are special sockets that will bite into the head of the stripped bolt, I use ones like these very often in the automotive world
    ...
  24. Replies
    28
    Views
    2,950

    Liqui Moly makes some really good oil ...

    Liqui Moly makes some really good oil

    https://products.liqui-moly.us/marine/marine-jet-ski-oil-sae-10w-40-1.html
  25. Replies
    53
    Views
    3,744

    It's going to be a very reliable machine when...

    It's going to be a very reliable machine when you're all done with it! I'm looking forward to seeing more pictures. That's a lot of metal in the pto housing, do you have any damage done to the...
Results 1 to 25 of 152
Page 1 of 7 1 2 3 4