Search

Type: Posts; User: king

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. Replies
    13
    Views
    228

    I think you should replace bolts with nuts if you...

    I think you should replace bolts with nuts if you tighten them because they are stretch when you tight them and in cars the same thing and there is a special tool to measure how much it stretch and...
  2. Replies
    12
    Views
    467

    thank you blakegjones...

    thank you blakegjones
  3. Replies
    4
    Views
    150

    No, I have the service manual and I know that if...

    No, I have the service manual and I know that if my crankcase have no mark and the crankshaft have mark I should got black bushing as I see from my service manual and if my con rod have mark and...
  4. Replies
    4
    Views
    150

    My bad story with bushing ultra 250x

    Hello everybody

    I buy new crankshaft from Kawasaki dealer but before this. I bought new bushing from the dealer and they choose it for me after I bring my used crankshaft with the crankcase to...
  5. Replies
    12
    Views
    467

    Thank you for your explanation. Now, I have...

    Thank you for your explanation.

    Now, I have another problem the oil pump shaft come inward and outward by hand is this normal ?
  6. Replies
    12
    Views
    467

    Thanks for everybody Ok, now I understand I...

    Thanks for everybody

    Ok, now I understand I should do Myself method like what he say I should turn wrench from straight 0 degrees until wrench points to 120 degrees no matter where nut corner...
  7. Replies
    12
    Views
    467

    But, not all nuts are one corner is straight (0...

    But, not all nuts are one corner is straight (0 degree) some of them between of straight (between 0 degree) .

    how can I tight them

    ...
  8. Replies
    12
    Views
    467

    How to tight connecting rod nut ???

    Hello everybody

    Today I install the new connecting rod on my new crankshaft but the problem was after I tight them 21.6 N.m with torque wrench I dont know how to tight the nut 120 degree more.
    ...
  9. Replies
    4
    Views
    199

    Yes ,the failure on my original motor involved...

    Yes ,the failure on my original motor involved spun and these are the pictures of the two connecting rod:
    ...
  10. Replies
    4
    Views
    199

    Connecting rod not fit

    Hello everybody


    Today when I assemble my ultra 250x 08 engine I face this problem , there are two connecting rod the caps does not fit on them and when I try to install it in my new crankshaft...
  11. Replies
    32
    Views
    3,098

    Hello everybody Finally, I end with buying new...

    Hello everybody

    Finally, I end with buying new crankshaft but now I want to be sure if my engine case is in good condition or not. And if any one have advise tell me before I start rebuild.
    ...
  12. Replies
    0
    Views
    156

    WTB - Parts ULTRA 300X impeller shaft

    Hi,

    I want Kawasaki 13107-0728 impeller shaft or 13107-0764 to upgrade my ultra 250x jet pump. Anyone know online site or person sell it around $45.

    thank you
  13. Replies
    63
    Views
    2,207

    Wow excellent thread !!! I work in same project...

    Wow excellent thread !!! I work in same project and its also, 08 250x ultra

    I hope not face the same problem because I spent until now 2k just for the parts :facepalm:
  14. Thread: Stator difference

    by king
    Replies
    0
    Views
    89

    Stator difference

    Hi,

    I have kawasaki ultra 250x and the stator has no connector in it.It was removed so, I want to buy complete used stator.
    And my question is there any difference between (2004-2014 STX STX12F...
  15. Replies
    2
    Views
    176

    Ok, how can I know if my jet pump is upgraded or...

    Ok, how can I know if my jet pump is upgraded or not?

    thank you
  16. Replies
    2
    Views
    176

    08 250x ultra chains

    Hi,

    I have 08 Kawasaki 250x ultra and I buy everything new include crankshaft, but my question is do I need to replace timing and oil pump chain? Also, its important to upgrade the jet pump or not...
  17. Replies
    6
    Views
    247

    You mean chop test or choke test? If I open the...

    You mean chop test or choke test?
    If I open the carbs, should I rebuild them or no need ?
  18. Replies
    6
    Views
    247

    Thank you Teemu I will do what you say and I hope...

    Thank you Teemu I will do what you say and I hope the carbs need just clean
  19. Replies
    6
    Views
    247

    I just recently change them with new one and they...

    I just recently change them with new one and they run just for 15 min so, I think they should be in good condition.
  20. Replies
    6
    Views
    247

    SUV1200 Shutoff while ride

    Hi

    Yesterday, I takeout my Yamaha SUV 1200 01 from storage in my garage after winter when I run it outside the water on it trailer it run very good. Then I take it to the sea it run good but while...
  21. Replies
    2
    Views
    249

    Hi nmpeter...

    Hi nmpeter

    I use long bolt but its come out in one side and other side it stuck in pin.

    what you mean ''vanes'' you mean the (lobes=rotor) ?
  22. Replies
    2
    Views
    249

    250x Supercharger stuck rear housing

    Hi,

    I have problem with my kawasaki 250x ultra 08. The rear housing wouldn't come out it stuck in it place.

    anyone have idea to open it?

    ...
  23. Replies
    0
    Views
    204

    250x Supercharger without shims !!!!!

    Hi,

    Today I open my Kawasaki 250x ultra 08 supercharger to clean it inside and to replace bearings, But when I remove the damper no shim come with it after that I open the pulley hub also no shims...
  24. Replies
    32
    Views
    3,098

    Hi, I want to know the 13031-3741 of 04-06...

    Hi,

    I want to know the 13031-3741 of 04-06 Kawasaki Jet Ski STX15F will fit on my Kawasaki ultra 250x 08 or not ? and Kawasaki 250x ultra crankshaft number is 13031-3741 the shape exactly same but...
  25. Replies
    32
    Views
    3,098

    OK. Now I understand So, either I grind journals...

    OK. Now I understand So, either I grind journals to last available oem bushing size or I weld it then grind it to stock size ?

    thank you for everybody who help me
Results 1 to 25 of 64
Page 1 of 3 1 2 3