Search

Type: Posts; User: tiderider

Page 1 of 8 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    46
    Views
    1,788

    Edelbrock has the rebuild kits for the Riva...

    Edelbrock has the rebuild kits for the Riva branded RRFPR.
  2. Replies
    50
    Views
    1,870

    I would get rid of it instead, take your small...

    I would get rid of it instead, take your small purchase loss and run..
  3. Replies
    50
    Views
    1,870

    Ouch!!! SBT! Don't use their connecting rod...

    Ouch!!! SBT! Don't use their connecting rod bolts. Bad experience in the past, i ended up sending them back to SBT, poor quality, it was like the bolt threads were cross threaded from factory..
  4. Replies
    5
    Views
    167

    Yes, it would easier and cleaner to pull the...

    Yes, it would easier and cleaner to pull the engine.
  5. Replies
    15
    Views
    594

    The head does not have to come off in order to...

    The head does not have to come off in order to replace the crankshaft. The rocker arm does in order to simplify timing, etc.
  6. A Good Seadoo 4 tec machine shop in Washington?

    Hi, does anyone know of a good machine shop in Washington state for the seadoo 4 tecs? Looking to find a better option than sending it off to another state every time something needs done.. Looks...
  7. Replies
    15
    Views
    594

    Main or lower 8 x bolts do not need replacing,...

    Main or lower 8 x bolts do not need replacing, they can be reused.
    I just installed a complete WSM set of bearings. Crankshaft main bearings, counter balance bearings, connecting rod bearings and...
  8. Replies
    50
    Views
    1,870

    Make sure all the fuses are good and that none...

    Make sure all the fuses are good and that none are missing..
  9. Replies
    4
    Views
    344

    Find a used one or bite the bullet for a new one....

    Find a used one or bite the bullet for a new one. Dealer will marry it to the cluster in no time.
  10. Replies
    50
    Views
    1,870

    The junk yard would be a good place to take it..

    The junk yard would be a good place to take it..
  11. It was an online seller who had 1 last set in...

    It was an online seller who had 1 last set in stock.. Good timing!! $60 is connecting rod bolts alone if I would have replaced only 1 OEM con rod.. Molnar con rods come with ARP2000 reusable bolts....
  12. Replies
    15
    Views
    1,173

    It was probably never installed.

    It was probably never installed.
  13. Thank you for this GREAT advice! I just...

    Thank you for this GREAT advice!
    I just purchased a New set of Molnar Connecting rods for $300.. Early Black Friday!!
    I installed a set in the first rebuild and honestly, they are VERY NICE.
  14. If you go with a Fizzle F1000 you may experience...

    If you go with a Fizzle F1000 you may experience a lot of condensation getting into the air intake manifold... You may think its leaking as well but its not, just very efficient. I personally have to...
  15. WSM crankshaft, Counter balance, Connecting rod, half rings bearings?? Any Good?

    Wow! Its like almost $300 to buy a full set of 4 tec OEM bearings with the seadoo brand on them...
    I have in the past purchased SBT half thrust rings for the 4 tec engines and honestly they were...
  16. Reuse stock connecting rods from failed engine??

    I picked up a really nice 2006 4 tec block from a GTI 130 with very few hours on it. Its so clean looking that you can eat off it.. Machinist will determine to bore, if so, how much oversized..
    From...
  17. Looks like the 2006+ are hollow due to the...

    Looks like the 2006+ are hollow due to the crankcase venting changes in 2006. Thank you
  18. WTB CP pistons or equivalent STD .25mm or .5mm Oversized

    Building an engine and looking for anyone who has a set of 3 kicking around that are within specs and not worn out of service life.
    I may be needing standard, .25mm or .5mm. Waiting for the great...
  19. Mix and matching counter balance with crankshafts

    Hi, I am putting together a 4 tec engine as a winter project. I am purchasing separate crank shaft and counter balance.
    I believe the crankshaft would be balanced from factory and the seller is...
  20. Straight Brass Male with barb end for head bleeder hose. Size/Specs.

    Hi, would anyone know what are the dimensions for the straight brass fitting which has a male threaded end on 1 side and a barb end on the other for the cooling system bleeding off the back head...
  21. I got PLAY TIME on mine. I get many asking if...

    I got PLAY TIME on mine. I get many asking if they can play with me... LOL..
  22. Wow! This has really become a truly helpful...

    Wow! This has really become a truly helpful thread.
    The big players come out with great knowledge off season!
    Sounds like I am pretty much dead on with my AFRs and should simply stick to 94...
  23. I have a RRFPR, I am just concerned that lowering...

    I have a RRFPR, I am just concerned that lowering the pressure to perhaps 55 psi instead of 58 psi to achieve the leaner .5afr may also reduce fuel supply to the 60lb injectors at 8500 rpms to a...
  24. Hi, thank you for the info. I am unable to see,...

    Hi, thank you for the info. I am unable to see, read or change ignition timing with my 2007 Siemens ECU and Riva tune with PLX logger set up. The engine has been rebuild with .5mm oversized pistons....
  25. Its a risk item.. I rebuild one a while back that...

    Its a risk item.. I rebuild one a while back that had many years, and with 150 hours on the original rebuild (Most updated kit). It was just like new, even the slip was dead on. I guess its a combo...
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4