Search

Type: Posts; User: 2fast4u

Page 1 of 8 1 2 3 4

Search: Search took 0.03 seconds.

  1. yes but the cruse control function will NOT work.

    yes but the cruse control function will NOT work.
  2. Thread: Water in hull

    by 2fast4u
    Replies
    33
    Views
    3,391

    My ski is totally dry inside after a 120 mile...

    My ski is totally dry inside after a 120 mile river ride, no water at all, if there is water in your ski you have a leak unless you take water in around the seat, handle bars or front cowl . 350+...
  3. Replies
    9
    Views
    404

    100% CORRECT this is why these skis are hard to...

    100% CORRECT this is why these skis are hard to start the first time after sitting for months.
  4. Replies
    8
    Views
    371

    replace sparkplugs re test first

    replace sparkplugs re test first
  5. Replies
    42
    Views
    2,120

    I think the machine work charges were $75.00 It...

    I think the machine work charges were $75.00 It was done to reduce the rotational weight so the clutch rpms would slow down faster when the clutch sprag un locked from the supercharger this helped...
  6. Replies
    42
    Views
    2,120

    R&D use to offer this service before they closed...

    R&D use to offer this service before they closed up. I have the weight info before and after machining if I can find it. Here is the in for for you. pictures and weights...
  7. Replies
    42
    Views
    2,120

    unsprung weight usually refers to anything on the...

    unsprung weight usually refers to anything on the car that is Not supported by the suspension . like the wheel, brakes , rear end, lower control arms, ect. sprung weight is anything that the...
  8. Replies
    22
    Views
    2,623

    Looking close at the photo where there thumb is I...

    Looking close at the photo where there thumb is I see heavy cavitation burns on the edge of the prop blades and also some cavitation pitting starting on the blade surface . this is caused by the...
  9. Replies
    16
    Views
    1,232

    when side gaping the sparkplug be care full and...

    when side gaping the sparkplug be care full and do not let the file touch the center electrode only remove material from the ground strap electrode.
  10. Replies
    16
    Views
    1,232

    when you change the original gap on a sparkplug...

    when you change the original gap on a sparkplug say from .038 (out of the box specification) to say .020 (desired plug gap) once the sparkplug has been run and heated and cooled several times the...
  11. Replies
    6
    Views
    460

    small fuel filters in each carb stopped up. R&R...

    small fuel filters in each carb stopped up. R&R carbs.
  12. SOLD Buy the parts from Butterbean 29512, I have had...

    Buy the parts from Butterbean 29512, I have had dealings with him in the past stand up guy for sure. Tommy Jordan
  13. Tell me more on how to mod the ride plate, Thanks

    Tell me more on how to mod the ride plate, Thanks
  14. more than likely your oem battery can not reach...

    more than likely your oem battery can not reach 100% charge.
  15. Me too, send me a pm

    Me too, send me a pm
  16. Replies
    12
    Views
    1,222

    given the fact that you stated 14 mph winds the...

    given the fact that you stated 14 mph winds the water had to be chopped up and that a lone can cost you mph. plus dealing with windy conditions cost you speed as well, since it is cool conditions now...
  17. Replies
    8
    Views
    556

    one question. what is your end desire with the...

    one question. what is your end desire with the ecm plugs and diagraham you have posted? what is your objective?
  18. Replies
    12
    Views
    1,222

    since you have valve retainers in place I would...

    since you have valve retainers in place I would raze the rev limiter to 9000 and retest ski first to see if you can get closer to 8800 to 8900 rpms if you are on the limiter hard you can not get the...
  19. Replies
    3
    Views
    169

    you might get better results if you posted this...

    you might get better results if you posted this in the 4 stroke forum more guys follow that section of the forum I think
  20. Replies
    18
    Views
    1,386

    clutch ,clutch , clutch, clutch that's all I have...

    clutch ,clutch , clutch, clutch that's all I have to say about that!
  21. Replies
    18
    Views
    1,386

    replace clutch again, use only Yamaha lube oil!

    replace clutch again, use only Yamaha lube oil!
  22. follow your vent line from tank up and be sure it...

    follow your vent line from tank up and be sure it is not pinched or kinked . also check valve in vent line should have a arrow on it pointing to gas tank showing a flow going to tank.
  23. you need to repost this in the Yamaha 4 stroke...

    you need to repost this in the Yamaha 4 stroke section to get better reply, How ever there should never be a vacuum in your fuel tank. some moderate pressure as the check valve will let air in and...
  24. Replies
    12
    Views
    838

    just clutch, pump gasket, o rings (4) and banjo...

    just clutch, pump gasket, o rings (4) and banjo washers (4) O ring and washers can be reused but I like to replace them to prevent any kind of leak. plus it never hurts to have spares just incase...
  25. I replaced my rivets with small stainless screws...

    I replaced my rivets with small stainless screws and stainless self locking nuts and flat washers much easier if you ever need to remove the trim again.
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4