Search

Want to buy or barter for a working MFD part # 3280307 for a 99 SLX. Old part # is 2872638

Have MSX140 and Virage parts to barter with. Let me know what you need.

I have a running 2004 MSX140. I can swap the EMM from the 2003 into it. I assume I shouldn't run it much due to the injector programming issues.

Thanks for everyone's opinion. Still pondering which way to go. Probably have 6 weeks before I dive into it. Would like to know if the EMM is good or not before I decide. Suggestions on who to send...

Thanks, so just plug the pulse port if I use carb bottom end with the Ficht heads? I looked at sourcing DW a few months ago and reached out to a couple of people but didn't get much of a response or...

Hello all. Just picked up an extremely clean 2003 MSX140 with a bad motor. Clean as in it has been garaged it's whole life and has little to no scratched or dings. Also freshwater and 128 hours.
...

No Instructions on the backing. It is adhesive glue on the back of the label though.

Thanks. Just to be clear, you also coat the surface with soapy water first then position the decal on the hull.

So pull the backing page off with the glue/adhesive exposed and place with soapy water. The adhesive will then stick once water and soap dries?

Hello, I am restoring a 96 Hurricane and 96 SLTX. I have some new OEM (3M) stickers for both skis, but of course, they are 24+ years old now.

Is there any trick to applying them due to their age?...

http://greenhulk.net/forums/attachment.php?attachmentid=468940&stc=1http://greenhulk.net/forums/attachment.php?attachmentid=468941&stc=1http://greenhulk.net/forums/attachment.php?attachmentid=468942&s...

http://greenhulk.net/forums/attachment.php?attachmentid=468931&stc=1http://greenhulk.net/forums/attachment.php?attachmentid=468932&stc=1http://greenhulk.net/forums/attachment.php?attachmentid=468934&s...

Hey CliffsidePM, let me know if you want to sell it. Also looking for 1341193 bearing carrier. Came on 1997 Hurricanes

Don't know about the originals as mine were missing when I bought the ski. The new ones hold well though. And for $10/pr, not that big of risk to try

Just got one from michaeltash2.

PM sent

Looking for a ride plate for a Polaris Hurricane. Condition is not critical. Going to cut it up for an extension on my stock one.

Parting a 2004 MSX140

Engine is currently spoken for
Harness, magneto, flywheel are available (no EMM or sensors)
Cowl is available but previous owner spray painted parts.
Handle bars available...

QC10PEP

Well thankfully it was something simple. I purchased and downloaded the PDF manual and read through it.

Found 2 things wrong.
1. Checked the plugs and they were the wrong ones. Put the Champion...

http://greenhulk.net/forums/attachment.php?attachmentid=467726&stc=1http://greenhulk.net/forums/attachment.php?attachmentid=467727&stc=1http://greenhulk.net/forums/attachment.php?attachmentid=467728&s...

Haha. I know but why not make it and keep it simple if you have all the parts on hand?

I work on German cars as a hobby and swapped TDI's into quite a few that were gassers. The fuel injection and...

Thanks. Will check with Lakeside Tech. Did check compression and have 140-145 acorss all 3.

May just make it simple and put the carb'd 1200 I have in it. LOL

Hello, picked up a 2004 MSX140 over the weekend. When I orginally looked at it, it did run but was really rough and backfired a few times.

Got it home and now it will turn over, but appears it is...

So looking at a 110. I work on VW/Audis a lot and have the VCDS Vagcom cable. It can read both CAN and K-line. I have a few VW harnesses laying around that I can grab a female OBD connector from. Can...

My son is selling his 96 Yamaha Wave blaster. 760 twin carb. Runs great. Has great compression. Just went through the carbs. Installed a primer. Very reliable and fun ski.

It's not a beauty queen...