Search

Type: Posts; User: Tom V

Page 1 of 8 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    199
    Views
    15,844

    Cycle Springs will bring a 2012 Yamaha FXHO...

    Cycle Springs will bring a 2012 Yamaha FXHO Cruiser, this will be the first time the general public will see this machine, What a great suprise for the 1st ski fest held in Clearwater.
  2. Replies
    114
    Views
    20,970

    Guys please understand I like visiting this site...

    Guys please understand I like visiting this site and reading different posts and topics you discuss, but everytime someone starts a SBT bashing thread people come out of the woodwork that have not...
  3. Replies
    114
    Views
    20,970

    If any one would like info on SBT products and...

    If any one would like info on SBT products and our proccedures please feel free to contact me through a private message or contact me at 1877-330-0231, I will be more than happy to answer your...
  4. Replies
    114
    Views
    20,970

    The Guy just wants to take stabs at SBT so no...

    The Guy just wants to take stabs at SBT so no matter what we say he will keep moving along and try to provoke others to join him. Sorry if I have offended you and your buddy. This site loves drama.
  5. Replies
    114
    Views
    20,970

    Bill, seriously your acting like a jack ass. And...

    Bill, seriously your acting like a jack ass. And your a moderator?
  6. Replies
    114
    Views
    20,970

    We did reman cranks for a divison of Yamaha for a...

    We did reman cranks for a divison of Yamaha for a while, they seemed pretty happy with them.
  7. Replies
    114
    Views
    20,970

    I'll answer anything anyone asks, I have been...

    I'll answer anything anyone asks, I have been working here at SBT for 4 yrs, before that I ran the service department at a Sea-doo and Polaris dealership since 1999. I'm Sea-doo factory trained and...
  8. Replies
    114
    Views
    20,970

    I think R&D copied those from Wave Eater, It is a...

    I think R&D copied those from Wave Eater, It is a great idea and has helped a lot of yamaha owners, to bad yamaha didnt think of it first.
  9. http://www.shopsbt.com/tour.htm

    http://www.shopsbt.com/tour.htm
  10. Replies
    13
    Views
    6,085

    At this point the best thing to do is to have all...

    At this point the best thing to do is to have all the old codes cleared out. Then re-read to see what stays active. Could be any thing from a bad coil,bad injector, old fuel foulded plug etc.
  11. Replies
    15
    Views
    4,331

    Robert, The 1st 3 engines you installed from us...

    Robert, The 1st 3 engines you installed from us (SBT) toasted the bearings before it ever got out of your shop this is correct, If you recall the engine I installed for you YES THE 4th one, I put...
  12. Your not using a RFI case then. all RFI cases...

    Your not using a RFI case then. all RFI cases have the waterjacket area and should be used, and the crank isnt working because the flywheel key way area is cut different for a RFI motor. RFI and carb...
  13. Yep, you have it correct, depending on what...

    Yep, you have it correct, depending on what bearing we are using we may have to trim the seal nubs. We build with both seals but at some point will use the late model only.
  14. Replies
    18
    Views
    7,850

    The bearing you see is the latest that seadoo...

    The bearing you see is the latest that seadoo uses, its rating is now the same as the SBT one, 26000 rpm still not 45000 but better, their original was 8k, do the research and you will see, also blue...
  15. Replies
    18
    Views
    7,850

    240859240860240861

    240859240860240861
  16. Replies
    18
    Views
    7,850

    Most people do not have a press in their garage,...

    Most people do not have a press in their garage, the instructions state using a block of wood, TAP the shaft lightly to slide the bearing down into position, it does not say Hammer the bearings into...
  17. Replies
    3
    Views
    682

    Dont put oil in the gas

    Dont put oil in the gas
  18. Replies
    18
    Views
    7,850

    SBT says to use the washers with ALL rebuild kits...

    SBT says to use the washers with ALL rebuild kits they sell, its listed as the last step in the instructions. To eliminate the confusion on what housing gets it and what doesn't get it, We say use it...
  19. If a guy wasn't good about cleaning out his ski...

    If a guy wasn't good about cleaning out his ski and used it in salt water alot, the salt water would rust out the rear seal and cause an air leak and take out the rear cylinder, this wasn't good if...
  20. Warrantee issues

    Warrantee issues
  21. If you guys would look at the location of the pto...

    If you guys would look at the location of the pto bearing next to the web on the guys crank you will see the bearing is not as close to the web as an o.e.bearing sits, this is why the seal looks like...
  22. Replies
    35
    Views
    4,665

    Some of you Guys know who I am and some dont, I...

    Some of you Guys know who I am and some dont, I do work for SBT and run the tech department, I have a long back round with Polaris watercraft and Sea-doo, If I can be of assistance please ask, I can...
  23. Replies
    57
    Views
    8,455

    Sorry its the circut breaker in the e/box, part...

    Sorry its the circut breaker in the e/box, part number 2434011, I had one on a Genesis go bad and caused some odd electrical issues.
  24. Replies
    57
    Views
    8,455

    Try replacing or bypassing the relay in the e/box

    Try replacing or bypassing the relay in the e/box
  25. Replies
    57
    Views
    8,455

    Check for an exhaust leak in the ski, check all...

    Check for an exhaust leak in the ski, check all the blue hoses for damage, it could have a small leak and be choking out the engine.
Results 1 to 25 of 184
Page 1 of 8 1 2 3 4