Search

Page 1 of 2 1 2

Search: Search took 1.00 seconds.

  1. Replies
    29
    Views
    784

    Do yourself a fAvour and make sure you get...

    Do yourself a fAvour and make sure you get submersible fuel line or you will end up having a bad day again.
  2. Replies
    3
    Views
    184

    So the best i could measure .533 to .535”...

    So the best i could measure .533 to .535” variation between all 3 bores top to bottom no real differences.
  3. Replies
    3
    Views
    184

    I have one in a box at home. I will measure it...

    I have one in a box at home. I will measure it when I get home from work. But my guess it will not be tapered
  4. Replies
    17
    Views
    602

    I use one bottle of Lucas to a tank of fuel if I...

    I use one bottle of Lucas to a tank of fuel if I can’t find 94 octane fuel. Just note it is hard on plugs and sensors(all octane boosters). I have also seen where guys run it through with every tank...
  5. Replies
    9
    Views
    425

    Do you have to wait no. Some flash right from day...

    Do you have to wait no. Some flash right from day one but in my personal experience waiting for 5 hours or so is a great idea just to let any serious mechanical issue show if there is going to be one.
  6. Replies
    52
    Views
    3,482

    I would not be to concerned with the colour of...

    I would not be to concerned with the colour of you oil unless it is milky or smells like pure gas. If you do not get the system 100% clean you will end up with tinted oil quickly.
  7. Replies
    16
    Views
    732

    I would start with some fuel treatment/injector...

    I would start with some fuel treatment/injector cleaner first.

    Then to remove the injectors I would download the service manual for all the proper steps. What I usually do is run the motor and...
  8. Replies
    16
    Views
    732

    You probably have a dirty Injector/ bad fuel. I...

    You probably have a dirty Injector/ bad fuel. I have had that happen a couple times after storage. Same symptoms
  9. Make sure there are no raised edges/high spots or...

    Make sure there are no raised edges/high spots or anything that can break off and send it. Have seen many engines with that and never an issue.
  10. Replies
    3
    Views
    409

    There are a few ways gas clr ac coil cleaner ...

    There are a few ways
    gas
    clr
    ac coil cleaner
    degreaser
    i soaked mine in gas then rinsed with water and dish soap to remove gas residue
  11. Replies
    5
    Views
    582

    Poll: You should be fine. I believe the manual says to...

    You should be fine. I believe the manual says to blow the system out with 50-55 psi for winterizing
  12. Obviously a dialed in ski thru the whole range is...

    Obviously a dialed in ski thru the whole range is best but your not going to burn Down a motor at idle and cruise being a little lean. You will how ever at wot.

    “peak torque is the hot spot for...
  13. I would keep using the 94 octane fuel. you...

    I would keep using the 94 octane fuel.
    you already have a rrfpr I would drop a psi at a time till you get the wot afr you want. Specially if it’s .5 to rich across the board. Wot is really the only...
  14. Yes a front mount set up is pretty safe for water...

    Yes a front mount set up is pretty safe for water ingestion. This was my old rxp with kanaflex up to the front.
    https://m.youtube.com/watch?v=tbCF81HXIcE
  15. Replies
    51
    Views
    3,756

    View Post

    So I’m going to bump this back up. I found a set of BRT tubes or pipes on eBay for a decent deal. Item number 333303516728 on eBay. I thought I usually buy Riva or fizzle to give something else a...
  16. Replies
    27
    Views
    1,935

    they only thing you can do to make it better is...

    they only thing you can do to make it better is in the tune. You need a proper tune and the right type of fuel for your application
  17. I’ll give you those are better then worm gear...

    I’ll give you those are better then worm gear clamps. I just took one of those out on a charge tube with being a little over snug tight
  18. I removed all the worm gear clamps on the exhaust...

    I removed all the worm gear clamps on the exhaust and intercooler piping and replaced them with t bolt clamps. I’ve never had good luck with worm gear clamps.
  19. With the pc and auto tune 100% you can make...

    With the pc and auto tune 100% you can make adjustments with the 300 pod.
    now why if your running the pc and auto tune not use the pod to data log and make changes with simple plugging in of a card....
  20. Replies
    23
    Views
    1,604

    what I don’t get is if the hose clamp and carbon...

    what I don’t get is if the hose clamp and carbon rings are such a common issue? Why do guys not look at them or inspect their skis? 99% of the issues could be avoided if people payed attention to the...
  21. Replies
    49
    Views
    4,099

    first time riding was 1994 on a gtx. Don’t...

    first time riding was 1994 on a gtx. Don’t remember much about it I was only 8 lol
  22. Replies
    12
    Views
    760

    Do you have any intake temp comparisons between...

    Do you have any intake temp comparisons between factory and the Riva cooler
  23. Replies
    3
    Views
    288

    .018-.022 are great place to be around

    .018-.022 are great place to be around
  24. Thread: Vins and ecus??

    by 05_RXP
    Replies
    19
    Views
    726

    there is JesusG and Brian R in tech support. I’ve...

    there is JesusG and Brian R in tech support. I’ve talked to both quickly they both seem very helpful and knowledgeable
  25. Thread: Vins and ecus??

    by 05_RXP
    Replies
    19
    Views
    726

    Looks like dealer must have changed the vin in...

    Looks like dealer must have changed the vin in the ecu. Only thing that makes snese
Results 1 to 25 of 32
Page 1 of 2 1 2