Search

Type: Posts; User: 2fast4u

Page 1 of 8 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    6
    Views
    357

    replace clutch again, use only Yamaha lube oil!

    replace clutch again, use only Yamaha lube oil!
  2. follow your vent line from tank up and be sure it...

    follow your vent line from tank up and be sure it is not pinched or kinked . also check valve in vent line should have a arrow on it pointing to gas tank showing a flow going to tank.
  3. you need to repost this in the Yamaha 4 stroke...

    you need to repost this in the Yamaha 4 stroke section to get better reply, How ever there should never be a vacuum in your fuel tank. some moderate pressure as the check valve will let air in and...
  4. Replies
    12
    Views
    609

    just clutch, pump gasket, o rings (4) and banjo...

    just clutch, pump gasket, o rings (4) and banjo washers (4) O ring and washers can be reused but I like to replace them to prevent any kind of leak. plus it never hurts to have spares just incase...
  5. I replaced my rivets with small stainless screws...

    I replaced my rivets with small stainless screws and stainless self locking nuts and flat washers much easier if you ever need to remove the trim again.
  6. Replies
    15
    Views
    994

    SOLD You can buy this from dif2001. great honest guy...

    You can buy this from dif2001. great honest guy to deal with. No Junk sold by him. Tommy Jordan
  7. Replies
    10
    Views
    301

    5 to 5.5 Mpg is about all you can get at 5000...

    5 to 5.5 Mpg is about all you can get at 5000 rpms cruzing and avoid full throttle starts on a stock tune ski.
  8. I did not say a torch, use a heat gun. once the...

    I did not say a torch, use a heat gun. once the glue has been heated extreamly hot and then cools it will release from the hull.
  9. heat it with a heat gun really hot then pry it...

    heat it with a heat gun really hot then pry it off.
  10. Replies
    12
    Views
    563

    That is the way Yamaha does there part numbers...

    That is the way Yamaha does there part numbers when they make a design to a part number.
  11. Replies
    172
    Views
    74,510

    I have found that if you sand most of the threads...

    I have found that if you sand most of the threads smooth (leaving only small ridges )on the plug before u install it and tighten the clamp good it will not leak
  12. Replies
    172
    Views
    74,510

    Over the years lots of guys have tried this mod,...

    Over the years lots of guys have tried this mod, I have never seen anyone go back to the noise free flo because they lost speed. Tommy Jordan
  13. Replies
    12
    Views
    563

    It was my understanding the bolt from a 2015 and...

    It was my understanding the bolt from a 2015 and up sc ski has a bigger hole in it than a 2009 , the factory up graded this hole size.
  14. Replies
    2
    Views
    115

    That is a 1200 gpr grate, the gpr 800 grates are...

    That is a 1200 gpr grate, the gpr 800 grates are closed in more on the back corners where the water enters the ramp.
  15. Replies
    5
    Views
    195

    I suppect your shaft is Not the Problem. If your...

    I suppect your shaft is Not the Problem. If your shaft is I would only use OEM parts. More than likely you prop is the problem
  16. Replies
    8
    Views
    1,049

    guess it did not workout to good. 9 days since...

    guess it did not workout to good. 9 days since his first post and no pictures or results, Besides I thought this mod was only for fzr/fzs hulls.
  17. Replies
    7
    Views
    421

    If you do not change plugs at least buy a set and...

    If you do not change plugs at least buy a set and carry them along with your tool kit just incase you have a problem. I replace plugs and battery ever other year I put about 50 to 75 hours each year...
  18. Replies
    3
    Views
    252

    be sure you have pushed the hose that you cut the...

    be sure you have pushed the hose that you cut the end off of all the way back down on the box, sounds like it is not totally down all the way to where the hose locks back in the groove on the box ,TJ
  19. Replies
    7
    Views
    424

    supercharger clutch was not locking up had my ski...

    supercharger clutch was not locking up had my ski do the same thing from sitting all winter once the clutch locked and un locked a few times worked great the rest of the year.
  20. Replies
    11
    Views
    902

    Has Impros changed owners?

    Someone told me Dave Had retired and Sold Impros to a guy who use to work for Scat Trac Impellers. Can anyone confirm this for me?
  21. Replies
    11
    Views
    1,218

    if it is a late model engine that has the big cam...

    if it is a late model engine that has the big cam chain just remove valve cover and see what size cam chain is in it.
  22. here you go...

    here you go http://greenhulk.net/forums/showthread.php?t=117030&highlight=free+flow+w%2Fo+noise
  23. Replies
    39
    Views
    5,670

    I have nice wc-2 with alu. box and mag wheels,...

    I have nice wc-2 with alu. box and mag wheels, spare wheel, led lights, torsion axel I am going to sell it is in storage now, $1200 firm
  24. Replies
    15
    Views
    1,495

    you have not done any damage at all silicone is a...

    you have not done any damage at all silicone is a protectant/lube you should be good to go!
  25. shop vac will suck them up easy. These feet are...

    shop vac will suck them up easy. These feet are needed to protect fuel pump from rubbing a hole in fuel tank bottom.
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4