Search

Page 1 of 10 1 2 3 4

Search: Search took 1.00 seconds.

  1. Thread: Theft Proof Lock

    by ncdoo
    Replies
    18
    Views
    585

    No such thing :)

    No such thing :)
  2. Replies
    18
    Views
    871

    Pretty much that simple, and you don't really...

    Pretty much that simple, and you don't really need a tune. But I would install an external IC and you'll also need a prop. You'll need an entire 260 SC, at least the front cover. You may need the...
  3. Replies
    45
    Views
    1,036

    Make sure you replace it with OEM part# that ends...

    Make sure you replace it with OEM part# that ends with 042. There were a bad batch of chains that had different part #s.
  4. Thread: siphon oil

    by ncdoo
    Replies
    1
    Views
    134

    It will come out, just takes a while.

    It will come out, just takes a while.
  5. Replies
    36
    Views
    3,832

    Just heard that Atlantic Beach and Emerald Isle...

    Just heard that Atlantic Beach and Emerald Isle have closed their boat ramps, in hopes that it will slow the influx of ding batters coming down from Raleigh.
  6. Replies
    36
    Views
    3,832

    According to the NCWRC website, most ramps in NC...

    According to the NCWRC website, most ramps in NC should be open. I went out last weekend, and I think everyone else did too.
  7. Tilt the ski and trailer back, fill with water to...

    Tilt the ski and trailer back, fill with water to cover the rear area including the carbon seal area. If there's a leak, you should be able to see where's its coming from.
  8. Replies
    2
    Views
    323

    You could always get these but it may be cheaper...

    You could always get these but it may be cheaper just to pull the head.
    http://greenhulk.net/forums/attachment.php?attachmentid=459357&stc=1
  9. Replies
    45
    Views
    1,036

    Yes definitely.

    Yes definitely.
  10. Replies
    45
    Views
    1,036

    The motor has to come out and the have to split...

    The motor has to come out and the have to split the crankcase to get the new timing chain on. I'm pretty sure you also need to remove the rod caps to lift the crank enough to get the timing chain...
  11. Sticky: Since the nuts are machined for balancing, are...

    Since the nuts are machined for balancing, are you saying that whenever you have to adjust the slip, the SC will need to be rebalanced? I've seen balancing marks on the newer X-chargers but never had...
  12. Yes

    Yes
  13. Replies
    25
    Views
    2,079

    Actually its pretty nice, allows you to upgrade...

    Actually its pretty nice, allows you to upgrade to the 137 wheel without having to replace the rear housing.
  14. Replies
    25
    Views
    2,079

    You can rebuild it, I have run several wheels...

    You can rebuild it, I have run several wheels like that with no issues and no noticeable loss of boost. The cover is fine also.
  15. Replies
    35
    Views
    7,386

    The 215/255 OEM head gaskets are not prone to...

    The 215/255 OEM head gaskets are not prone to failure. Its not going to hurt to use a 300 gasket, but if you have other problems, the 300 gasket is not going fix it.
  16. Replies
    17
    Views
    1,013

    I would not mod an SBT engine. you're rolling the...

    I would not mod an SBT engine. you're rolling the dice with running it stock.
  17. Replies
    14
    Views
    1,069

    First you stated that he said it was just...

    First you stated that he said it was just rebuilt. That's obviously not the case. Seller misrepresented the item. Members need to know who the seller is so they can be " Careful what you buy" and...
  18. Replies
    6
    Views
    498

    I would go with the proven supertech valves. I...

    I would go with the proven supertech valves. I would not put cheap aftermarket valves in any of my skis, stock or modified.
  19. Sticky: What will they think of next, a maintenance kit...

    What will they think of next, a maintenance kit for maintenance free supercharger...
  20. Thread: 98 GS pump seal?

    by ncdoo
    Replies
    9
    Views
    668

    With silcone sealant, they're a PITA to get back...

    With silcone sealant, they're a PITA to get back off. I would go with rubber seal shpown on the other models.
  21. Replies
    2
    Views
    307

    No worries as long as water didn't get in the...

    No worries as long as water didn't get in the engine. I would check both electrical boxes for water. Make sure they're dry on the inside. Put it in the water and check for leaks. If none, you should...
  22. Thread: Water pump issue

    by ncdoo
    Replies
    30
    Views
    2,330

    If you're interested, PM me your email and I'll...

    If you're interested, PM me your email and I'll send you an electronic copy. I dont have one for your specific year but most of the engine information is the same from year to year.
  23. Replies
    28
    Views
    2,203

    He could have bought the head of eBay, he never...

    He could have bought the head of eBay, he never mentioned a name. IMO it should have been put in a plastic bag prior to taking it to be packed. Good look cleaning that mess up.
  24. Thread: ARP Head studs

    by ncdoo
    Replies
    4
    Views
    358

    SOLD I have some good used rod bolts and rocker arm...

    I have some good used rod bolts and rocker arm bolts, cheap... :)
  25. Replies
    30
    Views
    1,589

    You'll need to check the number located on the...

    You'll need to check the number located on the end of the valve stems, the bad ones start with the number 72, the good valves start with 75.
    http://greenhulk.net/forums/showthread.php?t=169011
Results 1 to 25 of 230
Page 1 of 10 1 2 3 4