Search

Type: Posts; User: kingofl337

Search: Search took 0.00 seconds.

  1. The jet pump is the only thing not rebuilt....

    The jet pump is the only thing not rebuilt. Everything else has been cleaned/rebuilt/or replaced. I checked the pump, changed the oil it was ok, but the slip ring was a little worn. Nothing major. It...
  2. New Plugs (Gapped), Replaced Coil, New Caps....

    New Plugs (Gapped), Replaced Coil, New Caps. Should the 720 still have lot to give after 1/2 throttle. Compression is 140.

    I understand it won't be as peppy as a sled but the motor doesn't seem to...
  3. 97 Gti 720 - Accelerator Pump an Upgrade or Not

    I have a 97 with the non accelerator pump single carb. It has a fresh engine 15hrs and rebuilt carb with a Makuni kit. Plugs look good. Iím still new to PWCs but the engine isnít neatly as snappy as...
  4. I was able to figure out that the previous owner...

    I was able to figure out that the previous owner had replaced the coil(s) pack and re-inserted the wires in the wrong order. Fixed that and cleaned up the contacts in the box and it fired first shot....
  5. Looking for Expert 2-Stroke Polaris PWC Service in New Hampshire / Massachusetts Area

    I have a 99 1050 SLTX that is refusing to catch after a complete top end rebuild. 120psi Compression, Pressure Tested, Spark, Fuel, Reeds Ok, new bendix, flywheel correctly on its key. It's all there...
  6. Replies
    1
    Views
    233

    Swap the injectors and see if the issue moves....

    Swap the injectors and see if the issue moves. Also run a compression test.
  7. Replies
    2
    Views
    195

    Check the plug gap is .020”

    Check the plug gap is .020”
  8. Replies
    12
    Views
    299

    Thanks for your advice guys, after you guys...

    Thanks for your advice guys, after you guys pointed me more towards ignition I tightened up the plug gap to 0.015 and it got better. So I stole coil from my 951 carb project and it cleared up...
  9. Replies
    12
    Views
    299

    Pretty sure centered on the stator bolt holes....

    Pretty sure centered on the stator bolt holes. That seems to be the consensus as the right setting.
  10. Replies
    12
    Views
    299

    If I keep going it will just keep on going, just...

    If I keep going it will just keep on going, just popping. It won’t accelerate though it if it’s popping. I think the plugs look ok chocolate brown on the ceramic. I haven’t tried new plugs, but I...
  11. Replies
    12
    Views
    299

    Motor was built by PWCEngine in New York,...

    Motor was built by PWCEngine in New York, compression is 130 on each cylinder. It includes a 2 year warranty so there is that. Seems low but I figured the motor is fresh and needs to run in more to...
  12. Replies
    12
    Views
    299

    1st - 2:44 2nd- 2:46

    1st - 2:44
    2nd- 2:46
  13. Replies
    12
    Views
    299

    97 GTI Backfire Problem

    Hello friends I am need of your wise assistance in curing a backfire problem.

    I have done the following:
    Rebuilt Motor w/all new gaskets
    Rebuilt and cleaned the carb with new Makuni kit, pop...
  14. Replies
    1
    Views
    82

    Polarix 1050 Bendix Problem??

    I have a new to me Polaris 1050 SLTX I received with the top end in parts and the exhaust missing. I replaced the whole top end, rebuilt fuel system, and found all the exhaust bits. So I have never...
Results 1 to 14 of 15