Search

Type: Posts; User: smokeysevin

Page 1 of 8 1 2 3 4

Search: Search took 0.04 seconds.

  1. I was going to suggest using marine tex on the...

    I was going to suggest using marine tex on the small chunk but then I saw the keel. It my need to get flipped and re-gelkoted.

    Sean
  2. Replies
    3
    Views
    98

    WTB - Parts Pm sent Sean

    Pm sent

    Sean
  3. Replies
    5
    Views
    168

    Check the thread in my signature. If you pull the...

    Check the thread in my signature. If you pull the pumps, don't crank the motor over with the starter. Only rotate the engine by hand.

    If the gauges are bad, I can flash the ecus to 2004 spec to...
  4. Replies
    15
    Views
    340

    You can probably move it forward if you pay...

    You can probably move it forward if you pay attention to the hull while doing so. If you do move it forwards, you will increase the tongue weight so be mindful of that.

    Sean
  5. Replies
    27
    Views
    506

    The one I am messing with is here:...

    The one I am messing with is here: http://greenhulk.net/forums/showthread.php?t=283069

    Sean
  6. Replies
    27
    Views
    506

    Checkout koso, I am playing around with one of...

    Checkout koso, I am playing around with one of their gauges now, seems reasonably well made.

    Sean
  7. Replies
    75
    Views
    2,243

    You are correct, the fitting can either be...

    You are correct, the fitting can either be silicone'd to the bulkhead (as stock does) or you can use the bulkhead washer as the fitting does in other applications.

    One other think I am...
  8. Replies
    75
    Views
    2,243

    http://greenhulk.net/forums/attachment.php?attachm...

    http://greenhulk.net/forums/attachment.php?attachmentid=455791&stc=1
    Dimensions are based on aeromotive fittings and 2008 rxt-x steering cable. Kawasaki cables are a little smaller in diameter but...
  9. Replies
    37
    Views
    9,574

    If my memory is correct, when this was brought up...

    If my memory is correct, when this was brought up a few years ago it came down to the seating position being the issue. Basically they claimed it was because you were riding on the pwc vs in a boat...
  10. Last time I looked they were like $120 Sean

    Last time I looked they were like $120

    Sean
  11. Replies
    75
    Views
    2,243

    I may have figured out a way to make control...

    I may have figured out a way to make control cable thru hull fittings for relatively little money.

    Start with a -10an bulkhead fitting and hard line nut.

    Drill the an fitting through with a...
  12. You can drill and tap the cover for a 1/8npt to...

    You can drill and tap the cover for a 1/8npt to hose fitting adapter but it will restrict the flow a bit. I looked into fabricating a replacement cover with 1/4npt threads but it was going to be too...
  13. Thanks for the reply. I got new oem seals in the...

    Thanks for the reply. I got new oem seals in the mail a few days ago but I am waiting on the tool to pull the coupler now. The bearings all feel good as do the connecting rods this was more for peace...
  14. Cool pictures, I am hoping to explore Buchanan at...

    Cool pictures, I am hoping to explore Buchanan at some point. Havasu also has some incredible views if you get out in that area.

    Sean
  15. Replies
    75
    Views
    2,243

    I gave a lot of thought to going that route for a...

    I gave a lot of thought to going that route for a number of reasons but ultimately for me the simpler way was to just use the doo setup as is. I am not thrilled about having the carbon seal setup but...
  16. Replies
    19
    Views
    1,051

    Are you talking about the older model STX1100?...

    Are you talking about the older model STX1100? Can you post a picture of the rideplate mod?

    Sean
  17. Replies
    1
    Views
    108

    Check X-H2o.com they are standup people and...

    Check X-H2o.com they are standup people and should be able to point you in the right direction.

    Sean
  18. Replies
    10
    Views
    432

    It is interesting they take the temp there at...

    It is interesting they take the temp there at all, I would have assumed that the critical temp would be at the manifold. Since the newer skis use plastic ones they don't heat soak nearly as bad.
    ...
  19. Kawasaki STXR 1200 ultra 150 crankshaft rebuilders?

    Who is the go-to crank servicer now? I have a stxr that I took apart and just want to make sure all is done correctly. I want seals replaced at a minimum. The bearings seem to be in good shape but...
  20. Replies
    75
    Views
    2,243

    Shoe and water inlets/outlets, steering and...

    Shoe and water inlets/outlets, steering and reverse position.

    The first issue is that the reverse position on the kawasaki is on the side while the doo is on the top.

    Sean


    455400
  21. Replies
    53
    Views
    3,063

    Plate looks to be the same. Sean

    Plate looks to be the same.

    Sean
  22. Replies
    20
    Views
    683

    It runs fine with the older full open fitting and...

    It runs fine with the older full open fitting and regular size hose. That is how the early model 15fs came.

    Sean
  23. Replies
    20
    Views
    683

    I know we are all friends here but maybe don't...

    I know we are all friends here but maybe don't mention that outside of the forum...

    Sean
  24. Replies
    75
    Views
    2,243

    Nasty 15f, oil leaked out when I pulled the...

    Nasty 15f, oil leaked out when I pulled the engine.

    Sean
  25. Replies
    75
    Views
    2,243

    Stxr internal hull, the oil tank leaked. Sean

    Stxr internal hull, the oil tank leaked.

    Sean
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4