Search

Type: Posts; User: TMiller

Page 1 of 8 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    4
    Views
    103

    FS $550 for everything

    $550 for everything
  2. Replies
    4
    Views
    103

    FS These heads use ADA domes which are available in...

    These heads use ADA domes which are available in many sizes. The will also do custom run domes very reasonable.
  3. Replies
    4
    Views
    103

    FS Ultra 150/stxr billet heads

    Skiworx billet heads + brackets with an assortment of interchangeable domes. 3 - 44cc domes and 2 - 42cc domes to suit stock pistons. 3 - 26.5cc domes brand new to suit flat top pistons. Would...
  4. Replies
    1
    Views
    66

    The 148mm kawi pump was also used in the stxr...

    The 148mm kawi pump was also used in the stxr which came with a 1200. In that boat they would hold up until until output reached about 200-225 hp. Also factor in that hull setup weighed at around 650...
  5. Replies
    17
    Views
    1,559

    Bushing taper faces toward crank like you said....

    Bushing taper faces toward crank like you said. Put the seal you originally had in middle to the side, you dont need it. The seal in the front position is smaller I think so no question where that...
  6. Replies
    17
    Views
    1,559

    The seal you have in the middle position in the...

    The seal you have in the middle position in the 1st pic is for a 1999 model year. The cases are different on the 99 where the groove in the case will line up with that seal. The middle seal for the...
  7. Replies
    1
    Views
    166

    Welcome to the forum. I am not sure what kind of...

    Welcome to the forum. I am not sure what kind of response you will get for this type of ski on here. I am not real familiar with these older standups but if I remember the 440 pump is an upgrade and...
  8. Replies
    12
    Views
    372

    How about the OP?

    How about the OP?
  9. Replies
    12
    Views
    372

    Any updates on this?

    Any updates on this?
  10. Replies
    19
    Views
    451

    Whoa! What the? Where did this guy come from ?

    Whoa! What the? Where did this guy come from ?
  11. Replies
    6
    Views
    166

    Did you consider getting a quote from a shop that...

    Did you consider getting a quote from a shop that specializes in fiberglass repair? A couple extra bucks may go a long way, especially considering you dont have any experience with this stuff. A shop...
  12. Replies
    6
    Views
    166

    That grinder would work (for a short time). You...

    That grinder would work (for a short time). You will need a backer - https://www.harborfreight.com/4-12-in-backing-pad-for-resin-fiber-discs-60290.html and a disc -...
  13. Replies
    6
    Views
    166

    I probably would have started by glassing the...

    I probably would have started by glassing the backside for reinforcement and to give something to work off, would still be a good idea to do that now. Any way , if you have an angle grinder maybe...
  14. Replies
    7
    Views
    476

    FS - Parts Whoa! Whoa! Are you suggesting he put his wife...

    Whoa! Whoa! Are you suggesting he put his wife in storage?
  15. Replies
    4
    Views
    153

    If the failure on your original motor involved...

    If the failure on your original motor involved spun or damaged rod bearings then the big end of the rod is likely out of spec and no good. Usually in that case the cap will be loose and slide right...
  16. Replies
    4
    Views
    194

    Yea.. If you cant find the carbs you may be in...

    Yea.. If you cant find the carbs you may be in over your head.
  17. Replies
    8
    Views
    306

    Doubt it. Sounds like too much drama for too...

    Doubt it. Sounds like too much drama for too little gain. Is the exhaust on the correct side?
  18. Thread: Wrong pitch?

    by TMiller
    Replies
    5
    Views
    147

    You really need an accurate tach to measure rpm....

    You really need an accurate tach to measure rpm. "I" would not rely on the factory tach for tuning. I am not familiar with the 140 pump but have noticed the pump tunnel on the ZXI 1100 is smaller...
  19. Thread: Wrong pitch?

    by TMiller
    Replies
    5
    Views
    147

    How are you measuring rpm and speed? What about...

    How are you measuring rpm and speed? What about installing a complete 900 pump?
  20. Replies
    20
    Views
    396

    1999 cases are unique in that the center crank...

    1999 cases are unique in that the center crank seal/groove is different than all other years. Not a big deal but doesnt look like that seal is available OEM anymore. I am doing a set of 99 cases now...
  21. Thread: 15F engine

    by TMiller
    Replies
    2
    Views
    156

    WTB I just sold one complete a couple months ago...

    I just sold one complete a couple months ago $1200 shipped. Let you know if another lands anytime soon.
  22. A friend of mine has a stock stxr impeller that...

    A friend of mine has a stock stxr impeller that was refurbed by skat 0 hours on it. Think he wants about $100 for it.
  23. Replies
    42
    Views
    2,233

    If it is the ecu then they should be able to find...

    If it is the ecu then they should be able to find a 310 that runs normal and swap that computer into the problem ski. If it doesnt fix it then something else is going on. Could also swap the other...
  24. Replies
    15
    Views
    597

    ~ 8 weeks until the 2020s are released. 80 mph ?...

    ~ 8 weeks until the 2020s are released. 80 mph ? Are we hoping for a bigger motor or 25lbs of boost or both ?
  25. Replies
    42
    Views
    2,233

    Who is responsible for solving this type of...

    Who is responsible for solving this type of issue, the dealer or Kawasaki? If it is the dealer can the buyer go and find a different dealer to fix it under warranty?
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4