Search

Type: Posts; User: Jkmike

Page 1 of 8 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    4
    Views
    777

    Just ordered a Hydroturf Cover for my RXT-X 260....

    Just ordered a Hydroturf Cover for my RXT-X 260. When you did yours did you leave the original cover on?
  2. How can I upload the logs?

    How can I upload the logs?
  3. Ill deff try it out, just got the ski all back...

    Ill deff try it out, just got the ski all back together with stock cone and started up today. So what about the cells in the 8520 Rpm column? With my peak RPM of 8700 I'm right in the middle of 37-33...
  4. My WOT ignition timing is at 33. These are the...

    My WOT ignition timing is at 33. These are the timing tables from my MaptunerX. Ignition 1 and 2 are the same but 3 is a little lower at 8500 rpm. I personally have never messed with the ignition...
  5. Better hookup and acceleration mainly.

    Better hookup and acceleration mainly.
  6. Thats for sure, but it also allowed me to correct...

    Thats for sure, but it also allowed me to correct the poor factory alignment, so it was worth it. I have seen stuffing as low as like 83-84 mph before. But I have since installed two 1" PRVs and that...
  7. It definitely makes it stuff sooner, that's for...

    It definitely makes it stuff sooner, that's for sure. But the hookup is awesome. Unfortunately 2010&2011 were the years the stock pump was the ride plate mounted style and I converted over to the...
  8. Very interesting. This actually supports my...

    Very interesting. This actually supports my current leading theory that most of my RPM issues are related to the fact that I am running a Solas 14 Vane pump, and I'm sure the lucky 13 cone isn't...
  9. My nozzle is currently bored to 85mm. But i could...

    My nozzle is currently bored to 85mm. But i could still open it up further, it's the solas nozzle that came with the 14 vane Solas pump. Not sure if it's a thicker casting than the stock nozzles.
  10. I have tried it before but I never logged when I...

    I have tried it before but I never logged when I did. Ill deff give it a shot again and make some logs this time. My goal right now is really more to just optimize my power and acceleration while...
  11. This is interesting. What pump and cone were you...

    This is interesting. What pump and cone were you running?
  12. I agree about the RPMs. These are about the same...

    I agree about the RPMs. These are about the same RPMs i was seeing when i had the 68-140 charger installed, although i will say that the performance throughout the rest of the RPM range was greatly...
  13. That's definitely worth a shot with the seat...

    That's definitely worth a shot with the seat spacers. But short of just removing the storage bucket for testing on purely flat water, i wouldn't want to ride without it. I almost always have to go...
  14. I have a Maptuner X with data logging, and i did...

    I have a Maptuner X with data logging, and i did extensive logging and tuning last season. As for my afr i am around 11.8 to 12.0 at 8700 rpms and 18.8 psi of boost. Riva claims the 142 should be...
  15. Impeller Advice Needed RXT-X 260 w/ 300 XXX 142 Charger Conversion

    Hey Yaw,

    I could use a bit of impeller/prop pitch advice. I am running a RXT-X 260 with a 300 XXX 142 Charger conversion and a fully built motor (See my sig for details). I am currently running a...
  16. Replies
    32
    Views
    1,832

    I would love to. But how can I log aa that data...

    I would love to. But how can I log aa that data without a Motec? If there its a way to do it with my Maptuner X that would be awesome.
  17. Replies
    32
    Views
    1,832

    It sounds like the heat sink option might do the...

    It sounds like the heat sink option might do the trick. Deff worth giving it a shot. My last Bosch LSU 4.9 sensor was actually doing fine when I was pulling it from the ski after every use, but then...
  18. Replies
    32
    Views
    1,832

    Thats kind of what I was assuming they were...

    Thats kind of what I was assuming they were talking about. Just looked up the innovate heatsink and it looks interesting. Wouldn't a bung extender or even the innovate heatsink reduce the accuracy of...
  19. Replies
    32
    Views
    1,832

    What is this extension yaw are talking about? I...

    What is this extension yaw are talking about? I am on my 3rd Bosch LSU 4.9 sensor.
  20. This kind of bs is exactly why I am the only one...

    This kind of bs is exactly why I am the only one who ever works on my skis. (Specialized machining work excluded)

    Sorry to hear about your troubles. I'm looking forward to seeing how this all...
  21. Replies
    4
    Views
    669

    SOLD Sold

    Sold
  22. Replies
    3
    Views
    575

    SOLD Sold

    Sold
  23. Replies
    3
    Views
    575

    SOLD Sale pending.

    Sale pending.
  24. Replies
    3
    Views
    575

    SOLD Price Drop $800 Braap

    Price Drop $800

    Braap
  25. Replies
    4
    Views
    669

    SOLD Price Drop $800

    Price Drop $800
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4