Search

Page 1 of 16 1 2 3 4

Search: Search took 1.00 seconds.

  1. Replies
    4
    Views
    212

    View Post

    Do a search for “longitudinal axis” as there is much info about this topic.

    Bottom line, your drive shaft should have no more than 1/4 to 3/16” play in the drive shaft.
    Mark the drive shaft with...
  2. This is what the thru hull adapter looks like on...

    This is what the thru hull adapter looks like on my 2010 TX for a 3 point engine alignment check.
  3. Great job finding the source of your cavitation!...

    Great job finding the source of your cavitation!

    Clearly, you need to replace all drive line components as yours is worn unevenly.

    drive shaft
    c clip
    carbon ring
    floating ring
    bellows
    PTO...
  4. Replies
    20
    Views
    932

    The floating ring (hat) and carbon ring just...

    The floating ring (hat) and carbon ring just don’t fail. Most of the problems with the drive line are poor engine to pump alignment, drive shaft spline failures, thru hull fitting, bellows, etc.
    ...
  5. Replies
    20
    Views
    932

    2 high capacity bilge pumps are very important,...

    2 high capacity bilge pumps are very important, especially since your going off shore so far!

    Having the thru hull fittings well above the water line easily in sight is your warning.

    Simple...
  6. Replies
    15
    Views
    814

    The link I posted on page 8, states test altitude...

    The link I posted on page 8, states test altitude 676m / 5500’.
  7. Replies
    26
    Views
    1,508

    Badass job Dave!

    Badass job Dave!
  8. Replies
    17
    Views
    789

    http://greenhulk.net/forums/showthread.php?t=14593...

    http://greenhulk.net/forums/showthread.php?t=145934

    Read the very first post from Greenhulk himself back in 2011 which clearly describes our ECM limiters.

    Minor overshoots of the limits are...
  9. Replies
    49
    Views
    3,787

    I’m not worthy, only 11.2 years thanks to my...

    I’m not worthy, only 11.2 years thanks to my brother in law 1tommygunner1927.

    It has been a hell of a journey............!
  10. No, the oil will come out front. About 2 quarts...

    No, the oil will come out front. About 2 quarts as there is about 5 quarts total in the engine.
  11. Replies
    12
    Views
    819

    Looks great! Replace the stock mats with...

    Looks great!

    Replace the stock mats with Hydro-Turf mats any color/pattern you want. Sold here in the Performance Store, for about $100.

    I replaced the stock ones on our 05 GTX and they made...
  12. Replies
    26
    Views
    1,525

    Ok Bob, I’ll come clean........I’ve been peeing...

    Ok Bob, I’ll come clean........I’ve been peeing in your gas so that you stay slower than me!
  13. Replies
    7
    Views
    796

    Ok, you can pee farther than I can! LOL Glade...

    Ok, you can pee farther than I can! LOL

    Glade Rider has run his 94.64567mph.........I have chosen to slow back down due to being a Senior citizen.

    Bottom line here is that either GRF Turbo...
  14. Replies
    40
    Views
    4,589

    Here is .80 lambda / 11.75 AFR snapshot on a...

    Here is .80 lambda / 11.75 AFR snapshot on a typical run. You can make the EGT go down with more fuel, knock adjustments, timing adjustments, etc, etc, etc and vice versa. Keeping temps below 1800*F...
  15. Thread: Bounce at 83+

    by jpt7779
    Replies
    10
    Views
    1,116

    Very common issue. As your fuel load gets lighter...

    Very common issue. As your fuel load gets lighter you have to run the trim down.
  16. If your engine to pump alignment is off, the nose...

    If your engine to pump alignment is off, the nose cone will never stay in place!

    The other option is to run it without the nose cone, works just fine.
  17. Thread: seadoo stand

    by jpt7779
    Replies
    26
    Views
    2,613

    We paid $375 + tax with casters and optional...

    We paid $375 + tax with casters and optional risers which are needed for S3/T3 hulls.
  18. Replies
    19
    Views
    1,342

    Read this thread for a start:...

    Read this thread for a start: http://greenhulk.net/forums/showthread.php?t=235606

    Do a search for PRV and you will see numerous threads with lots of ideas.
  19. Replies
    19
    Views
    1,342

    My 2010 T-X S3 hull would consistently stuff at...

    My 2010 T-X S3 hull would consistently stuff at 83-84 mph. I installed tunnel pressure sensor and logged it numerous times. Stuff always happened around 48 psi tunnel pressure and you could feel it...
  20. Thread: seadoo stand

    by jpt7779
    Replies
    26
    Views
    2,613

    439883439884439885 Scotty, yo momma and Evan...

    439883439884439885

    Scotty, yo momma and Evan are out on my ski ........... so I could take these pics just for you!!!!!!

    Note the optional higher riser which is needed for S3/T3 hulls, which is...
  21. Replies
    25
    Views
    1,252

    You can get the relay at any auto parts store...

    You can get the relay at any auto parts store with some quality wiring and do it your self much cheaper.
  22. Thread: seadoo stand

    by jpt7779
    Replies
    26
    Views
    2,613

    seadoo stand

    Triton makes an aluminum one that is far superior to my other one that I welded up myself.
    438807
  23. Replies
    17
    Views
    1,093

    Higher octane fuels are definitely NOT going to...

    Higher octane fuels are definitely NOT going to hurt performance and make your ski run very well. It is very noticeable.

    The issue is, are the gains worth the cost? Only you can determine if it...
  24. Replies
    2
    Views
    395

    If you used JB WaterWeld simply heat it up with a...

    If you used JB WaterWeld simply heat it up with a heat gun to remove it and access the bolts.

    Don't expect much from filling these holes...........
  25. Time for a new IC!

    Time for a new IC!
Results 1 to 25 of 400
Page 1 of 16 1 2 3 4