Search

Type: Posts; User: 05_RXP

Page 1 of 8 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    0
    Views
    49

    DIY spring compressor?

    Hey gents does anyone have any diy or homemade ideas for changing springs and retainers on a sea doo with the head still installed? I have a compression tester and leak down tester for the compressed...
  2. Replies
    7
    Views
    235

    As mentioned I would not be so worried about what...

    As mentioned I would not be so worried about what pitch you have the factory prop set at. Just have your factory impeller pitched to spin the rpm range you desire. If your sending out your impeller...
  3. Replies
    57
    Views
    4,520

    Yes

    Yes
  4. Replies
    30
    Views
    888

    Do yourself a fAvour and make sure you get...

    Do yourself a fAvour and make sure you get submersible fuel line or you will end up having a bad day again.
  5. Replies
    2
    Views
    187

    I would suggest you try and find a st3 hull and...

    I would suggest you try and find a st3 hull and t3 hull ski to test where you ride. The t3 hull on the newer Rxpx is amazing for chop. Although you still are going to get air and beat up a little in...
  6. Replies
    0
    Views
    152

    Dashpac creative solutions

    Hey gents just installing my dash pac. What creating solutions have you guys come up for mounting the module.
  7. Replies
    138
    Views
    7,096

    Can you confirm that the ski is taking the tune?

    Can you confirm that the ski is taking the tune?
  8. Replies
    9
    Views
    445

    I have a free flow which will probably turn into...

    I have a free flow which will probably turn into a thru hull really quickly.

    now who wants to talk how much rpm they picked up with their cams?
  9. Replies
    2
    Views
    147

    Proper engine alignment and do not run for...

    Proper engine alignment and do not run for extended periods of time out of the water.
    they are how ever considered to be a consumable/wear item
  10. Replies
    9
    Views
    445

    Thanks I am trying to add power with out having...

    Thanks I am trying to add power with out having the heat from the bigger chargers.

    can the cam be run on pump gas still?
  11. Replies
    9
    Views
    445

    Who wants to talk cams?

    I know a lot of guys are running cams with upgraded chargers.
    is there anyone one that is running a cam with a factory charger?
  12. Replies
    8
    Views
    281

    WTB Stroll through some of the sea doo groups on...

    Stroll through some of the sea doo groups on Facebook and I bet you change your mind. Guys have been showing them with blades ripped off, the sxx labels on them, new purchases dates within the last...
  13. Replies
    8
    Views
    281

    WTB With all the talk of these exploding. I would...

    With all the talk of these exploding. I would only buy new from reputable dealer that will take care of you if it does go boom.
  14. Replies
    3
    Views
    185

    So the best i could measure .533 to .535”...

    So the best i could measure .533 to .535” variation between all 3 bores top to bottom no real differences.
  15. If you need to tow I would use the 2 d rings On...

    If you need to tow I would use the 2 d rings On the lower hull. It may be harder to access fro. On the ski but it will be your most ridged point
  16. Replies
    3
    Views
    185

    I have one in a box at home. I will measure it...

    I have one in a box at home. I will measure it when I get home from work. But my guess it will not be tapered
  17. Replies
    3
    Views
    1,278

    FS I would say not likely with the thread going on...

    I would say not likely with the thread going on 10 years now.
  18. I would just keep and eye on it. Judging by the...

    I would just keep and eye on it. Judging by the size of your pistons the block has had some machine work done to it. It’s probably a little left over shavings. No matter how well you try you can...
  19. Replies
    10
    Views
    383

    I thought they were saying the found junk in the...

    I thought they were saying the found junk in the crank with out pulling the motor down.

    as to the milk brp part, dealers will say they change parts under warranty to get paid for labour and get...
  20. Replies
    10
    Views
    383

    So how exactly did they find debris in the crank?...

    So how exactly did they find debris in the crank? In theory if they found debris in the crank they should be pulling the motor. Sounds like they are trying to milk brp if you still have warranty.
  21. Replies
    52
    Views
    3,491

    Glad to see you got your fueling issue figured...

    Glad to see you got your fueling issue figured out. I would try to get your afrs up a little before you try tweaking your prop. You will definitely pick up some rpm by leaning out your afr. Also do...
  22. Replies
    17
    Views
    604

    I use one bottle of Lucas to a tank of fuel if I...

    I use one bottle of Lucas to a tank of fuel if I can’t find 94 octane fuel. Just note it is hard on plugs and sensors(all octane boosters). I have also seen where guys run it through with every tank...
  23. Replies
    5
    Views
    515

    I would not put the faith of your motor in that....

    I would not put the faith of your motor in that. Even if they were suppose to be but my guess is he was saying the je pistons run the same gap as factory.
  24. Replies
    122
    Views
    6,898

    I have to agree the question is what’s accuracy....

    I have to agree the question is what’s accuracy. I run some radar runs on my snowmobile. I have a handheld gps, Motec gps, VBOX sport and they use a stalker radar gun. On every pass guess many of...
  25. Replies
    18
    Views
    559

    The best thing I can tell you is make sure you...

    The best thing I can tell you is make sure you have good insurance. If someone want it bad enough there will be nothing that will stop them.

    You can slow them down however, I have seen guys jack...
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4