Search

Page 1 of 2 1 2

Search: Search took 1.00 seconds.

  1. Replies
    10
    Views
    917

    I filled mine with grease as I was putting it...

    I filled mine with grease as I was putting it back together. Once a year after that I add just one pump with my grease gun.
  2. Replies
    28
    Views
    2,314

    You press against the shaft on the other end. Not...

    You press against the shaft on the other end. Not the back of the coupler
  3. Replies
    6
    Views
    389

    It wasn't correct but I used a four way lug...

    It wasn't correct but I used a four way lug wrench centered on the coupler to grab four of the points and then used the driveshaft to hold the other end with a strap wrench around it and then into a...
  4. Thread: Paint bubbles

    by superair
    Replies
    36
    Views
    2,183

    I didn't get pics this weekend but I do have the...

    I didn't get pics this weekend but I do have the part numbers

    drain plug
    F3X-U2255-00-00 (need 2)

    Check Valve
    F3X-U7767-00-00 (need 1)

    Connector
    F3X-U8377-00-00 (need 2)
  5. Replies
    12
    Views
    992

    Seen this before; it is from cavitation. In the...

    Seen this before; it is from cavitation. In the SHO days people were cutting reliefs in their vains to eliminate this. See pics.
    Also search for a thread named SHO/FZR pump vien blowouts

    The one...
  6. Replies
    60
    Views
    4,429

    just have to give it the reach around :)

    just have to give it the reach around :)
  7. Replies
    60
    Views
    4,429

    I just rebuilt the one for my GP1800 and you can...

    I just rebuilt the one for my GP1800 and you can leave the coupler on the shaft. It presses out the threaded side. There is one seal on that side and the circlip for the bearing is in there that has...
  8. Replies
    9
    Views
    787

    Great job!! Glad you have it running.

    Great job!! Glad you have it running.
  9. Replies
    7
    Views
    593

    Yes

    Yes
  10. Replies
    7
    Views
    593

    Good luck to you. Don't fret too much just take...

    Good luck to you. Don't fret too much just take your time and it will go smoothly. Make sure you keep the caps and shims in order as well. I only take one off at a time.
  11. Replies
    9
    Views
    1,322

    That line is used for fuel management and a...

    That line is used for fuel management and a disruption from the blow off valve or surge could affect the fuel mapping causing a lean condition and so it has been advisable to leave it alone and tap...
  12. Replies
    6
    Views
    975

    I have both 2017 and 2019 cut by Jim; just...

    I have both 2017 and 2019 cut by Jim; just putting on the 2019 plate now. It will be a month or so before I have results though.
  13. Replies
    1
    Views
    347

    Just pull the cone and check for water in the...

    Just pull the cone and check for water in the pump. If it's not there then you should be OK. If you get the service manual you can see the specs if you want to check them though.
  14. Replies
    4
    Views
    1,476

    Found this in the search post #17 is from JD1. ...

    Found this in the search post #17 is from JD1.

    http://greenhulk.net/forums/showthread.php?t=190914

    Maybe the link will work. If not look up fzr cooling mods
  15. Replies
    4
    Views
    1,476

    I have a cooling recommendation from Dan with...

    I have a cooling recommendation from Dan with Jetdraft that I used. I'll find it scan and post for you. Don't know if it's the best option but it is what I have been running for years.

    Does anyone...
  16. Replies
    13
    Views
    1,546

    I only do it while the pump is out. place in a...

    I only do it while the pump is out. place in a vice shaft down then fill to top of pump body. I fill the cone with grease and let it mix on it's own while running.
  17. Replies
    5
    Views
    1,341

    I would be careful with any additives in a motor...

    I would be careful with any additives in a motor that has a sprag clutch
  18. Replies
    10
    Views
    1,338

    Below is an image from the Riva instructions....

    Below is an image from the Riva instructions. With the Worx regulator you only need to replace the factory regulator.




    http://greenhulk.net/forums/attachment.php?attachmentid=441905&stc=1
  19. Replies
    7
    Views
    777

    On a Garmin handheld GPS

    On a Garmin handheld GPS
  20. Have you checked the adjustment of the cable?...

    Have you checked the adjustment of the cable? With the bucket in position with the power off you should be able to remove the cable from the ball on the bucket without too much resistance. If this is...
  21. There was an issue around 2009 with the FZR and...

    There was an issue around 2009 with the FZR and maybe the SHO pump overstuffing and causing the ski to buck people. A simple change of intake grates fixed this. Also there was a minimum nozzle size...
  22. Replies
    27
    Views
    2,208

    FS - Parts Most people just cut or tuck the sensor above the...

    Most people just cut or tuck the sensor above the plate. I always remove mine including the wiring. The connector is behind the front storage cover and you can trace the wiring from the sensor to it....
  23. It is most likely a 400 grade of stainless. Same...

    It is most likely a 400 grade of stainless. Same as used on stainless steel exhaust systems in automobiles. This is ferritic stainless and used mainly because of it's ease of working with; it is also...
  24. The hull is painted with PPG automotive clear...

    The hull is painted with PPG automotive clear coat. The dry film is 1 to 1.2 mils. This is within range of the specification from the manufacture (PPG). Unfortunately this also is not very durable...
  25. Thanks Mark for the suggestion. It is being...

    Thanks Mark for the suggestion. It is being recommended by Dean's Team to use an R&D 83mm exit nozzle and thought if this would work then at least I have a little bit of flexibility for tuning.
Results 1 to 25 of 42
Page 1 of 2 1 2