Search

Type: Posts; User: K447

Page 1 of 8 1 2 3 4

Search: Search took 0.31 seconds; generated 58 minute(s) ago.

  1. Replies
    129
    Views
    1,651

    This is using the OHMS mode or the continuity...

    This is using the OHMS mode or the continuity test mode on the meter?
  2. Replies
    129
    Views
    1,651

    Both ignition coils measure the same? If yes,...

    Both ignition coils measure the same?

    If yes, seems unlikely both would fail at the same time, in the same way
  3. Replies
    1
    Views
    57

    From the factory? Yes, there is a 2.5mm step...

    From the factory? Yes, there is a 2.5mm step between the 155mm transom plate and the 160mm impeller area.

    You can have the transom plate machined to create a taper that matches the 160mm pump to...
  4. Replies
    129
    Views
    1,651

    Electrical testing must be accurate and...

    Electrical testing must be accurate and methodical.
    Confirm your test results, consider whether your test results could be misleading you.

    Do not jump to conclusions.
    ...
  5. Replies
    129
    Views
    1,651

    That is an auto-ranging multi-meter. Make sure...

    That is an auto-ranging multi-meter.
    Make sure you always check the range scale when reading the digits.

    https://testmeterpro.com/innova-3320/
    ...
  6. Welcome. Click this link, save it in your...

    Welcome.

    Click this link, save it in your bookmarks.
    Lots of useful info.
    http://polarispwcknowledge.shorturl.com/first-things-to-do

    CDI is the ignition system for a carburetor engine.
    EMM...
  7. Replies
    129
    Views
    1,651

    What plugs? Ignition coil ohm tests are just...

    What plugs? Ignition coil ohm tests are just using the ommeter and the coil itself.

    What meter are you using? What range was the meter showing when you tested the secondary coil resistance?

    Did...
  8. Replies
    129
    Views
    1,651

    Secondary coil would be the post that connects to...

    Secondary coil would be the post that connects to the spark plug wire ;)
  9. Replies
    6
    Views
    199

    The mid-wall is a composite material. I would not...

    The mid-wall is a composite material. I would not trust self-taping screws to work long term, as the hull flexes and bounces hard as you ride fast across rough water.

    Use stainless steel bolt...
  10. Replies
    129
    Views
    1,651

    Compare with specs from the service manual...

    Compare with specs from the service manual
  11. Thread: I Want A Divorce

    by K447
    Replies
    33
    Views
    2,870

    I am suspecting spam, when a first time poster...

    I am suspecting spam, when a first time poster includes a link to an outside web site.
  12. Sticky: Do you have an accurate tachometer installed? ...

    Do you have an accurate tachometer installed?

    What is the maximum sustained RPM you are seeing at full throttle on the water?

    What GPS speed are you seeing? At what altitude?

    What makes you...
  13. The Triton bunk mounts are offset where they are...

    The Triton bunk mounts are offset where they are attached to the bunk boards.

    You can swap the bunks end for end to shift whether the front or back end ‘sticks out more’.

    Also, the bunk...
  14. Replies
    129
    Views
    1,651

    Ohm tests of primary and secondary coils, to coil...

    Ohm tests of primary and secondary coils, to coil ground strap.

    And ground strap to the actual engine metal.

    Only other test is to swap in a known good coil.
  15. Replies
    129
    Views
    1,651

    I have had a Ficht ignition coil fail. Uncommon,...

    I have had a Ficht ignition coil fail. Uncommon, but possible. The ignition coils are mounted directly to the engine and these engines do vibrate.

    I have also seen the grounding of a Ficht...
  16. Replies
    15
    Views
    356

    Doubling the thickness of the wood bunks makes...

    Doubling the thickness of the wood bunks makes for a much stiffer bunk. It may conform to the hull shape less and have less flex when the trailer is bouncing over hard bumps.

    The taller/thicker...
  17. Replies
    129
    Views
    1,651

    Ohms is not a valid test for TPS. Where are you...

    Ohms is not a valid test for TPS. Where are you finding the info guiding you on your test methods?

    We are posting specific questions, and methods. You are often reporting hand waving answers, and...
  18. Replies
    15
    Views
    356

    One way to gain vertical clearance (lift the hull...

    One way to gain vertical clearance (lift the hull higher relative to the trailer frame) is to add 2x2 aluminium square tube (extruded box section) underneath each Triton factory bunk bracket.

    I...
  19. Replies
    26
    Views
    1,044

    The risk is real, even if local people are not...

    The risk is real, even if local people are not 'seeing' it.
  20. Replies
    129
    Views
    1,651

    If the Brown wire is not near zero volts during...

    If the Brown wire is not near zero volts during cranking, that means the EMM is NOT trying to start the engine.

    Either the EMM itself is not right or something feeding into the EMM is not giving...
  21. SOLD I am interested. It is this intake grate...

    I am interested.

    It is this intake grate RY22110, correct?

    https://www.4-tecperformance.com/index.php?main_page=product_info&cPath=16_82_94_288&products_id=5338&zenid=6i6jrfi4havnj8dsiukp4p6qs4...
  22. Replies
    17
    Views
    360

    The correct adjustment for a Ficht throttle cable...

    The correct adjustment for a Ficht throttle cable is to have a tiny bit of slack when throttle lever is not being touched. The throttle shaft and the throttle plates inside the Ficht throttle bodies...
  23. Replies
    22
    Views
    1,455

    If indeed your original clutch has begun to slip,...

    If indeed your original clutch has begun to slip, your use description still seems like a match for the factory clutch. Despite the apparent ‘early’ failure, I do not see a reason for the Yamaha...
  24. Replies
    129
    Views
    1,651

    View Post

    Loosen the fuel filler cap so you don’t accidentally pressurize the actual fuel tank.
  25. Replies
    3
    Views
    129

    Moved thread.

    Moved thread.
Results 1 to 25 of 192
Page 1 of 8 1 2 3 4