Search

Type: Posts; User: Jonesyfxr

Page 1 of 8 1 2 3 4

Search: Search took 0.01 seconds.

  1. Thread: Fzr seat

    by Jonesyfxr
    Replies
    4
    Views
    149

    WTB - Parts http://www.pwctoday.com/showthread.php?t=495014

    http://www.pwctoday.com/showthread.php?t=495014
  2. Thread: Fzr seat

    by Jonesyfxr
    Replies
    4
    Views
    149

    WTB - Parts There’s a guy parting a FZR on PWCToday

    There’s a guy parting a FZR on PWCToday
  3. Replies
    22
    Views
    706

    The “baffle” is actually like a trap door. It’s...

    The “baffle” is actually like a trap door. It’s designed to hold fuel around the pickups during cornering. They are known to hang up and prevent fuel from getting pulled into the pickups.
  4. Replies
    22
    Views
    706

    That's a great point. An easy mod to perform...

    That's a great point. An easy mod to perform also.
  5. Replies
    22
    Views
    706

    Those are pretty good numbers!! Sounds like...

    Those are pretty good numbers!! Sounds like you’re back at it!

    Be safe in the woods and get some venison for the table!
  6. Replies
    3
    Views
    157

    Checking in to see how you’re making out.

    Checking in to see how you’re making out.
  7. Replies
    22
    Views
    706

    Let us know what you find... inquiring minds...

    Let us know what you find... inquiring minds would like to know.
  8. Replies
    15
    Views
    445

    I'd use a hose clamp

    I'd use a hose clamp
  9. Replies
    3
    Views
    157

    Welcome to this page!!! TONS of knowledge here. ...

    Welcome to this page!!! TONS of knowledge here.

    Make sure you PV Servo is working as it should, as stated. Also check to make sure you have wave eater clips and PV couplers.
  10. Replies
    15
    Views
    414

    http://greenhulk.net/forums/showthread.php?t=30369...

    http://greenhulk.net/forums/showthread.php?t=30369

    Here ya go
  11. Replies
    15
    Views
    414

    No problem dude. Lots of good info there

    No problem dude. Lots of good info there
  12. Replies
    15
    Views
    414

    There’s a thread in How to section titled...

    There’s a thread in How to section titled “Jetting specs I have used”
  13. Replies
    15
    Views
    445

    From SBT: You test the pressure with a pop-off...

    From SBT:

    You test the pressure with a pop-off pressure gauge. With the regulator chamber open, wet the N&S with WD-40 or gas. With the pump body removed, attach the gauge to the fuel inlet...
  14. Replies
    15
    Views
    445

    Also... did you wet the gasket with oil during...

    Also... did you wet the gasket with oil during the install? And spray WD-40 in the carb before doing the pop off test?
  15. Replies
    15
    Views
    445

    View Post

    Donít quote me on this.... but I read somewhere that those pump bodies warp over time and need to be sanded flat on a piece of glass or thick plate steel.
  16. Replies
    15
    Views
    445

    I believe you test pop off on fuel inlet only.

    I believe you test pop off on fuel inlet only.
  17. Replies
    22
    Views
    706

    You’ll also need to perform this mod.... ...

    You’ll also need to perform this mod....

    http://greenhulk.net/forums/showthread.php?t=94630
  18. Replies
    22
    Views
    706

    The search feature is your friend.... ...

    The search feature is your friend....

    http://greenhulk.net/forums/showthread.php?t=177671
  19. Thread: Need advise

    by Jonesyfxr
    Replies
    18
    Views
    885

    View Post

    Iíve heard horror stories about SBT stuff.... just the opposite for WSM. Youíre on the right track.
  20. Replies
    306
    Views
    197,381

    Sticky: My pump bodies were pretty corroded. I had to...

    My pump bodies were pretty corroded. I had to sand mine smooth again. I have not tested the pop-off tho.
  21. Replies
    15
    Views
    884

    2-Stroke We finally rebuilt our carbs and installed the T...

    We finally rebuilt our carbs and installed the T handles. As my son wan iOS wing the last T handle, he dropped it... and put a nick in the tip. So, he learned a valuable lesson... and the carbs are...
  22. Replies
    22
    Views
    706

    Here is some information off the “How to”...

    Here is some information off the “How to” section.

    http://greenhulk.net/forums/showthread.php?t=70129

    But you need to remove the tamper proof caps to install t handles.
  23. Replies
    22
    Views
    706

    Ok, so you never installed t handles on the high...

    Ok, so you never installed t handles on the high and low speed adjusters? These skis are known to run lean from factory.
  24. Replies
    15
    Views
    884

    2-Stroke Glad you got it figured out dude! These 2 smokers...

    Glad you got it figured out dude! These 2 smokers can be a PITA!!
  25. Replies
    22
    Views
    706

    What are your carb settings? Usually, the...

    What are your carb settings?

    Usually, the plugs look similar. Kinda looks like you have one lean cylinder.

    Did you do a plug chop, or pull plugs after riding 20 minutes?
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4