Search

Type: Posts; User: BLASTER 1

Page 1 of 8 1 2 3 4

Search: Search took 0.01 seconds.

  1. View Post

    Here’s a picture http://greenhulk.net/forums/attachment.php?attachmentid=457972&stc=1http://greenhulk.net/forums/attachment.php?attachmentid=457973&stc=1
  2. I did the same on my 15 fz, I cut the sleeve off...

    I did the same on my 15 fz, I cut the sleeve off at the line on the trim adjuster. You can still adjust trim and use odi grips. I never adjusted the trim while under power, I thought something was...
  3. moparguy, Jettrim custom cover

    moparguy, Jettrim custom cover
  4. View Post

    I’m using 140mm odi grips, I put 1” long 7/8” bar stock that I installed on the ends of the bars to make them wider. I also drilled and tapped for a bigger end bolt. So far so good
  5. Replies
    126
    Views
    6,764

    [QUOTE=1_Fast_SHO;3054448] Hey, we are not all...

    Hey, we are not all wussy’s here in COMIFORNIA!
    The Democrats are ruining this state😢
  6. Replies
    126
    Views
    6,764

    View Post

    Hey we are not all wussy’s her in COMIFORNIA!
    The Democrats are ruining this STATE
  7. Its normal to be open at idle, your TB is closed...

    Its normal to be open at idle, your TB is closed so it’s just releasing what air your charger is pushing. It will close usually around the 5-6 thousand range of course it depends on what lb spring...
  8. Replies
    31
    Views
    2,050

    No, that should not or won’t have any effect on...

    No, that should not or won’t have any effect on slipping
    If it’s not the clutch I’ll make you one of my specialty drinks next time your in California
  9. Replies
    34
    Views
    2,189

    Still sounds like it’s your clutch, like others...

    Still sounds like it’s your clutch, like others have stated. Even if you can only spin the charger wheel one way doesn’t mean it’s good. If it has any movement or just slightly mushy it’s going out
  10. Replies
    8
    Views
    476

    The hull has a lot to do with how the ski turns....

    The hull has a lot to do with how the ski turns. Yes you can move where the steering cable attaches but be careful the fz sits higher on the water I’d hate to see you get tossed
  11. Replies
    31
    Views
    2,050

    I believe I’ve heard a few members here tried...

    I believe I’ve heard a few members here tried that process but never heard about the results
  12. Replies
    31
    Views
    2,050

    It’s not the bearing but the center gear that the...

    It’s not the bearing but the center gear that the sprags grab
  13. Replies
    31
    Views
    2,050

    Its all those sprags or fingers when it spins...

    Its all those sprags or fingers when it spins they grab the center bearing where you see is all pitted. Both the sprags and inner surface will wear thus it just spins without grabbing or sporadic...
  14. Replies
    31
    Views
    2,050

    That sound is normal, and your clutch is...

    That sound is normal, and your clutch is slipping. Time for a new one
    I wish these things had a external belt drive like the Kawi. I’d much rather replace a belt then having to dive into the front...
  15. Replies
    44
    Views
    3,905

    CJ, I think I’ve read twice here that your not...

    CJ, I think I’ve read twice here that your not using a intercooler at all, straight from charger to the throttle body right? That’s interesting. So how would it run if you were using a cooler
  16. Replies
    3
    Views
    322

    Nice, I like it! But you should go turbo right...

    Nice, I like it! But you should go turbo right away
  17. Replies
    2
    Views
    370

    Nice, I like it! But you should go turbo right...

    Nice, I like it! But you should go turbo right away
  18. Replies
    44
    Views
    3,905

    My kid is in the process of installing this on...

    My kid is in the process of installing this on his stage 3 FZS, can’t wait for the results
    If the results are favorable I might have to try it myself
  19. Thread: Lost 300rpms

    by BLASTER 1
    Replies
    27
    Views
    1,714

    Or possibly your clutch is starting to slip, not...

    Or possibly your clutch is starting to slip, not a lot but enough to lower your rpm’s
  20. Replies
    12
    Views
    911

    That tool is worth it makes replacement much...

    That tool is worth it makes replacement much easier. Depending on your location maybe you can borrow one. But remember you will be replacing the clutch again, sometimes sooner than later unfortunately
  21. Replies
    2
    Views
    201

    Buy one from jettrim, your choice of materials...

    Buy one from jettrim, your choice of materials and colors. You also should cover foam with plastic for waterproofing
  22. Replies
    47
    Views
    2,079

    In my opinion you don’t, but what I did is open...

    In my opinion you don’t, but what I did is open up the T under the exhaust to let more water to the oil cooler and cylinder block. Like I said in a couple posts before I’m going to experiment with...
  23. Replies
    47
    Views
    2,079

    The intercooler seemed more efficient and the oil...

    The intercooler seemed more efficient and the oil was cooler with no gio. The tune must be close to spot on in all rpm ranges
  24. Replies
    47
    Views
    2,079

    I’m actually going to be testing with the worx...

    I’m actually going to be testing with the worx engine cooling plate running 2 lines between the 2and 3 cylinders and possibly using The anode as a exit line but I’m not sure yet
  25. Replies
    47
    Views
    2,079

    We found that routing the intercooler directly...

    We found that routing the intercooler directly out and not routing from intercooler to the oil cooler suited us better but this is on a 17 GP and 16 fz
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4