Search

Type: Posts; User: king

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. Replies
    10
    Views
    280

    Thank you for your explanation. Now, I have...

    Thank you for your explanation.

    Now, I have another problem the oil pump shaft come inward and outward by hand is this normal ?
  2. Replies
    10
    Views
    280

    Thanks for everybody Ok, now I understand I...

    Thanks for everybody

    Ok, now I understand I should do Myself method like what he say I should turn wrench from straight 0 degrees until wrench points to 120 degrees no matter where nut corner...
  3. Replies
    10
    Views
    280

    But, not all nuts are one corner is straight (0...

    But, not all nuts are one corner is straight (0 degree) some of them between of straight (between 0 degree) .

    how can I tight them

    ...
  4. Replies
    10
    Views
    280

    How to tight connecting rod nut ???

    Hello everybody

    Today I install the new connecting rod on my new crankshaft but the problem was after I tight them 21.6 N.m with torque wrench I dont know how to tight the nut 120 degree more.
    ...
  5. Replies
    4
    Views
    156

    Yes ,the failure on my original motor involved...

    Yes ,the failure on my original motor involved spun and these are the pictures of the two connecting rod:
    ...
  6. Replies
    4
    Views
    156

    Connecting rod not fit

    Hello everybody


    Today when I assemble my ultra 250x 08 engine I face this problem , there are two connecting rod the caps does not fit on them and when I try to install it in my new crankshaft...
  7. Replies
    32
    Views
    3,019

    Hello everybody Finally, I end with buying new...

    Hello everybody

    Finally, I end with buying new crankshaft but now I want to be sure if my engine case is in good condition or not. And if any one have advise tell me before I start rebuild.
    ...
  8. Replies
    0
    Views
    116

    WTB - Parts ULTRA 300X impeller shaft

    Hi,

    I want Kawasaki 13107-0728 impeller shaft or 13107-0764 to upgrade my ultra 250x jet pump. Anyone know online site or person sell it around $45.

    thank you
  9. Replies
    63
    Views
    2,011

    Wow excellent thread !!! I work in same project...

    Wow excellent thread !!! I work in same project and its also, 08 250x ultra

    I hope not face the same problem because I spent until now 2k just for the parts :facepalm:
  10. Thread: Stator difference

    by king
    Replies
    0
    Views
    81

    Stator difference

    Hi,

    I have kawasaki ultra 250x and the stator has no connector in it.It was removed so, I want to buy complete used stator.
    And my question is there any difference between (2004-2014 STX STX12F...
  11. Replies
    2
    Views
    164

    Ok, how can I know if my jet pump is upgraded or...

    Ok, how can I know if my jet pump is upgraded or not?

    thank you
  12. Replies
    2
    Views
    164

    08 250x ultra chains

    Hi,

    I have 08 Kawasaki 250x ultra and I buy everything new include crankshaft, but my question is do I need to replace timing and oil pump chain? Also, its important to upgrade the jet pump or not...
  13. Replies
    6
    Views
    232

    You mean chop test or choke test? If I open the...

    You mean chop test or choke test?
    If I open the carbs, should I rebuild them or no need ?
  14. Replies
    6
    Views
    232

    Thank you Teemu I will do what you say and I hope...

    Thank you Teemu I will do what you say and I hope the carbs need just clean
  15. Replies
    6
    Views
    232

    I just recently change them with new one and they...

    I just recently change them with new one and they run just for 15 min so, I think they should be in good condition.
  16. Replies
    6
    Views
    232

    SUV1200 Shutoff while ride

    Hi

    Yesterday, I takeout my Yamaha SUV 1200 01 from storage in my garage after winter when I run it outside the water on it trailer it run very good. Then I take it to the sea it run good but while...
  17. Replies
    2
    Views
    242

    Hi nmpeter...

    Hi nmpeter

    I use long bolt but its come out in one side and other side it stuck in pin.

    what you mean ''vanes'' you mean the (lobes=rotor) ?
  18. Replies
    2
    Views
    242

    250x Supercharger stuck rear housing

    Hi,

    I have problem with my kawasaki 250x ultra 08. The rear housing wouldn't come out it stuck in it place.

    anyone have idea to open it?

    ...
  19. Replies
    0
    Views
    198

    250x Supercharger without shims !!!!!

    Hi,

    Today I open my Kawasaki 250x ultra 08 supercharger to clean it inside and to replace bearings, But when I remove the damper no shim come with it after that I open the pulley hub also no shims...
  20. Replies
    32
    Views
    3,019

    Hi, I want to know the 13031-3741 of 04-06...

    Hi,

    I want to know the 13031-3741 of 04-06 Kawasaki Jet Ski STX15F will fit on my Kawasaki ultra 250x 08 or not ? and Kawasaki 250x ultra crankshaft number is 13031-3741 the shape exactly same but...
  21. Replies
    32
    Views
    3,019

    OK. Now I understand So, either I grind journals...

    OK. Now I understand So, either I grind journals to last available oem bushing size or I weld it then grind it to stock size ?

    thank you for everybody who help me
  22. Replies
    32
    Views
    3,019

    My problem now is the bushing. Because I take the...

    My problem now is the bushing. Because I take the crankshaft to our Kawasaki dealer and he take measure to give me the right size for bushing then they give me a number of bushing and they tell me...
  23. Replies
    32
    Views
    3,019

    thank you rlovebk...

    thank you rlovebk.
    I have question
    do you work before in Kawasaki engine ?

    If you tell me about common problem of this year of Kawasaki 250x ultra 08

    because I am new in Kawasaki and I buy...
  24. Replies
    32
    Views
    3,019

    Hi SplishSplash...

    Hi SplishSplash

    Today I check the bearing faces on the upper half and lower half both still there bushing in good shape and not shredded only that two bushing of connecting road journal goes bad....
  25. Replies
    32
    Views
    3,019

    Should I polish the journal? and what about oil...

    Should I polish the journal? and what about oil pump I should rebuild it or I need to check it first?
Results 1 to 25 of 60
Page 1 of 3 1 2 3