Search

Type: Posts; User: mittens

Page 1 of 8 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    66
    Views
    3,923

    haha yep. Turd! haha still ran mid 80s just...

    haha yep. Turd! haha still ran mid 80s just surprised so much variance. and wanted to make sure is normal ha.
  2. Replies
    66
    Views
    3,923

    so double checked oil, removed 4 Oz slowly. its...

    so double checked oil, removed 4 Oz slowly. its right at the top dot on one side barley over on the other if you flip it. The last 2 inch of the dip stick are off set form some reason.

    Then took...
  3. Replies
    25
    Views
    1,493

    It's the check valve in the vent clog... and...

    It's the check valve in the vent clog... and sucked my 09 fzr tank so far into its self it cracked it.
  4. Replies
    27
    Views
    947

    hell If I get a season out of one that would be...

    hell If I get a season out of one that would be awesome. I am worried about getting the whole day ha

    but so far this one has lived... riding tomorrow so we will see.
  5. Replies
    66
    Views
    3,923

    But 300 rpm from 10 degrees? I mean at some...

    But 300 rpm from 10 degrees? I mean at some point it has to stop falling off or a stock one would barley run... I guess I expect it to very to some degree. just like a car, but that's a big...
  6. Replies
    66
    Views
    3,923

    So took it out yesterday 64 water temp and 80...

    So took it out yesterday 64 water temp and 80 degrees out. 11.5 WOT throttle. so it did come down with some warmer weather and some humidty. more then I would have thought. but that's means it...
  7. Replies
    27
    Views
    947

    the same as the wide band o2. you just thread it...

    the same as the wide band o2. you just thread it in the bung, and then the sensor threads into it

    The DOT on one of the 6 sides of the nut part indicates which way the forward hole is. you want...
  8. Replies
    27
    Views
    947

    I ran mine for a 3rd time yesterday the whole...

    I ran mine for a 3rd time yesterday the whole day. 20 starts and stops, and lots of idle, and was still alive. I did pull it when I got home, and am also now shove the hose of a wet vac up the...
  9. I understand, but the Yamahas the clutch slips...

    I understand, but the Yamahas the clutch slips ALOT every time rpms decreas, shut down, jump, what ever.

    vs the seadoo design that slips if it has too otherwise the washers are tight and...
  10. That's my biggest hang up, is how come no one has...

    That's my biggest hang up, is how come no one has made billet light weight gears, and no clutch.... everyone says it will strip teeth, and bla bla bla.


    But I have yet to prove it has to have a...
  11. Replies
    27
    Views
    947

    I would use the heat sink before the bung...

    I would use the heat sink before the bung extender.

    the heat sink still goes down into the stream with a metal cavity, this cavity has a hole in the front side so the exhaust flows into the...
  12. Thread: Opinion needed

    by mittens
    Replies
    13
    Views
    282

    I have herd they go 1000s of hours. but I have...

    I have herd they go 1000s of hours. but I have ZERO experience.

    my GP1200 had 100 hours and sold at 150
    my 09 FZR had 102 hours on it and sold ar 149.5
    my 16 FZ had 19.5 on it and now 21.5 ha
    ...
  13. Replies
    27
    Views
    947

    I use the innovative heat sink. Protects the...

    I use the innovative heat sink. Protects the sensor from water splashes. has a hole you a line with incoming flow, and the it exits down. Not sure how it would change the reading as its reading...
  14. I can se this point as the back pressure there is...

    I can se this point as the back pressure there is helping to stop the blower speed before reentry.

    BUT at the same token, the BOV allowing it to free spin longer allows it to keep its RPMs closer...
  15. A rev limit I snot throttle actuated it never is,...

    A rev limit I snot throttle actuated it never is, Normally fuel or ignition. and with this being a factor boosted motor I would hope and assume its ignition, leaning it out by injectors to limit is...
  16. Replies
    3
    Views
    201

    I would run the Riva or Worx, the stack is hot...

    I would run the Riva or Worx, the stack is hot air, and down low, easier to suck water if you did get bunch in there.

    riva seals up and botls high like a snorkel.
  17. Replies
    5
    Views
    399

    FS i messaged you about pressure regulator.

    i messaged you about pressure regulator.
  18. Replies
    6
    Views
    829

    My fizzle has its own line, and then after the...

    My fizzle has its own line, and then after the fizzle it Ys and pisses out both factory pissers.

    The factory intercooler line, feeds a anode for more cooling.
  19. Replies
    1
    Views
    245

    M understanding is the SVHO ride FX skis share...

    M understanding is the SVHO ride FX skis share the same ECU.

    but if something does not have ride they don't.
  20. Sanded and acitoned. Then did black 4200 and...

    Sanded and acitoned. Then did black 4200 and installed it back, and torqued 19.5lbs
    http://greenhulk.net/forums/attachment.php?attachmentid=459358&stc=1
  21. Yes the air can stop. Don't dissagree my blown...

    Yes the air can stop. Don't dissagree my blown 427 has a blow off/bypass valve as well. But this threat was if one was needed for the clutch so saying the blow back will spin it backwards is what I...
  22. Just finished getting the old stuff off the...

    Just finished getting the old stuff off the ski/hull that is the worst part. removeing seat supports, and pump less then 45 min..

    filling voids, in transom, and sanding/ cleaning lips for new...
  23. Replies
    19
    Views
    1,027

    haha good stuff in here

    haha good stuff in here
  24. Replies
    26
    Views
    588

    I work as a gov contractor on a Gov facility....

    I work as a gov contractor on a Gov facility. last Tuesday they shut us all down to Telework. which is rare for the Gov world.

    they where not sure if the contracts would allow them to pay us...
  25. Pulled mine off this morning, just filled bottom...

    Pulled mine off this morning, just filled bottom and top voids with 2 part epoxy, added a drop or 2 of black epoxy die. Because I had some. Ha
    will now clean transom glue off and then scratch and...
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4